DeWalt DWE46150 Traducido De Las Instrucciones Originales página 21

4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job
better and safer at the rate for which it was
designed.
WARNING: The use of any accessory
or attachment or performance of any
operation with this tool, other than those
recommended in this instruction manual
may present a risk of personal injury.
b) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
Use the power tool, accessories and
c)
tool bits etc., in accordance with these
instructions taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) SERVICE
a) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Surface Grinding Shroud Safety
Rules
• The shroud must be securely attached
to the power tool and positioned for
maximum safety, so the least amount of
wheel is exposed towards the operator.
The shroud is designed to collect dust and help
protect the operator from accidental contact
with the wheel.
• Do not use accessories which are not
specifically designed and recommended
by the tool manufacturer. Just because the
accessory can be attached to your power tool,
it does not assure safe operation.
• Only use dry diamond surface cup wheels
with this surface grinding shroud. The
surface grinding shroud is not intended to be
used with standard grinding, cut-off, cup wheels
or wire brushes.
• The rated speed of the accessory must
be at least equal to the maximum speed
marked on the power tool. Accessories
running faster than their rated speed can break
and fly apart.
• Hold power tool by insulated gripping
surfaces only, when performing an
operation where the cutting accessory
may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool
"live" and shock the operator.
• Always use side handle. Tighten the handle
securely. The side handle should always be
used to maintain control of the tool at all times.
• Do not use a damaged accessory. Before
each use inspect the accessory such
as diamond wheel for chips and cracks,
backing pad for cracks and tear or
excess wear. If power tool or accessory is
dropped, inspect for damage or install an
undamaged accessory. After inspecting
and installing an accessory, position
yourself and bystanders away from the
plane of the rotating accessory and run
the power tool at maximum no-load speed
for one minute. Damaged accessories will
normally break apart during this test time.
• When starting the tool with a new or
replacement wheel, hold the tool in a
well protected area and let it run for one
minute. If the wheel has an undetected crack
or flaw, it should burst in less than one minute.
Never start the tool with a person in line with the
wheel. This includes the operator.
• Wear personal protective equipment.
Depending on application, use face
shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron
capable of stopping small abrasive or
workpiece fragments. The eye protection
must be capable of stopping flying debris
generated by various operations. The dust
mask or respirator must be capable of
filtrating particles generated by your operation.
Prolonged exposure to high intensity noise may
cause hearing loss.
• Position the cord clear of the spinning
accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be
pulled into the spinning accessory.
• Never lay the power tool down until the
accessory has come to a complete stop.
The spinning accessory may grab the surface
and pull the power tool out of your control.
• Do not run the power tool while carrying
it at your side. Accidental contact with the
spinning accessory could snag your clothing,
pulling the accessory into your body.
english
19