V2 KIBO-R Instrucciones De Instalación página 11

Customization of the access code
OPERATIONS TO BE MADE ON THE KEYPAD
1. Key in C + PROGRAMMING CODE + C
Signalling: 1 BEEP of 1,5 sec. + L1 on for 1,5 sec.
2. Key in within a minute the KEY 2 + C
Signalling: 2 BEEP + L1 flashes 2 times
3. Key in the NUMBER OF THE CHOSEN CHANNEL + C
Signalling: 1 BEEP of 1 sec. + L1 flashes 2 times
4. Key in the NEW ACCESS CODE + C
Signalling: 1 BEEP of 1 sec. + L1 flashes 2 times
5. Repeat the NEW ACCESS CODE + C
Signalling: - 1 BEEP of 3 sec. + L1 on if the operation is
correct;
- short flashes of the L1 if incorrect
Disabling a channel
OPERATIONS TO BE MADE ON THE KEYPAD
1. Key in C + PROGRAMMING CODE + C
Signalling: 1 BEEP of 1,5 sec. + L1 on for 1,5 sec.
2. Key in within a minute the KEY 2 + C
Signalling: 2 BEEP + L1 flashes 2 times
3. Key in the NUMBER OF THE CHOSEN CHANNEL + C
Signalling: 1 BEEP of 1 sec.
4. Key in the KEY 0 + C
Signalling: 1 BEEP of 1 sec.
5. Repeat the KEY 0 + C
Signalling: - 1 BEEP of 3 sec. + L1 on if the operation is
correct;
- short flashes of the L1 if incorrect
3. WORKING MODE: ROYAL, 53200 or
PERSONAL PASS
Select the working mode according to the kind of remote controls
already used in the system.
OPERATIONS TO BE MADE ON THE KEYPAD
1. Key in C + PROGRAMMING CODE + C
Signalling: 1 BEEP of 1,5 sec. + L1 on for 1,5 sec.
2. Key in within a minute the KEY 3 + C
Signalling: 3 BEEP + L1 flashes 3 times
3. • Key in the KEY 1 + C to select ROYAL mode
• Key in the KEY 2 + C to select 53200 mode
• Key in the KEY 3 + C to select PERSONAL PASS mode
• Key in the KEY 4 + C to select P.PASS mode with
MONOSTABLE operating logic*
Signalling: 1 BEEP of 1 sec.
4. Repeat to confirm (1 + C or 2 + C or 3 + C or 4 + C)
Signalling: - 1 BEEP of 3 sec. + L1 on if the
operation is correct;
- short flashes of the L1 if incorrect
4. DIP-SWITCH CODE (only version
Royal/53200)
The factory dip-switch code set for channel 1 is 0101010101 00.
If other remote controls are already stored on the receiver, the dip-
switch code of the keypad has to be set with the same sequence of
the one set on the dip-switch of the remote control.
The dip-switch of the remote control is made up by a series of 12
micro switches set to ON or OFF.
To set the same code on the keypad, it is necessary to key in a code
made up of 12 digits: those will be 0 or 1, depending on the position
of the micro switches on the remote control
- micro switch set to ON = 1
- micro switch set to OFF= 0
If the transmitter is single channel, the dip-switch to be set
coincides with the position of the 12 micro switches.
If the transmitter is two-channel and the key stored is 2, the
dip-switch code to be set coincides with the position of the 12 micro
switches. If the key stored on the receiver is the key 1, the dip-switch
code coincides with the position of the micro switches from 1 to 10
plus the 2 digit 00.
If the transmitter is four-channel, the dip-switch code to be set
coincides with the position of the micro switches from 1 to 10 plus 2
digits, which are:
• 00 if the key stored on the receiver is the key 1
(e.g. 1010101010 00)
• 10 if the key stored on the receiver is the key 2
(e.g. 1010101010 10)
• 01 if the key stored on the receiver is the key 3
(e.g. 1010101010 01)
• 11 if the key stored on the receiver is the key 4
(e.g. 1010101010 11)
If no transmitter has been stored on the receiver, the
dip-switch code can be set entering a random sequence of 12 digits
0 or 1.
OPERATIONS TO BE MADE ON THE KEYPAD
1. Key in C + PROGRAMMING CODE + C
Signalling: 1 BEEP of 1,5 sec. + L1 on for 1,5 sec.
2. Key in within a minute the KEY 4 + C
Signalling: 4 BEEPs + L1 falshes 4 times
3. Key in the NUMBER OF THE CHOSEN CHANNEL + C
Signalling: 1 BEEP of 1 sec. + L1 falshes 4 times
4. Key in the CHOSEN DIP-SWITCH CODE + C
Micro switch set to ON = 1
Micro switch set to OFF = 0
Signalling: - 1 BEEP of 3 sec. + L1 on if the
operation is correct;
- short flashes of the L1 if incorrect
- 11 -