Chicco Next2me Magic Manual Del Usuario página 15

the crib, that objects or bedding items do
not fall into the crib.
COMPONENTS
A. Leg rest with wheels
A1. Height adjustment button
A2. Rocking function button
A3. Height indicator
A4. Telescopic foot release button
A5. Telescopic feet
A6. Wheels with brakes
A7. Central support structure slot
A8. Bottom bar slots
A9. Upper structure fastening support
A9.1. Upper structure release button
B. Bottom bar
C. Central support structure
D. Crib structure
D1. Fabric
D1.1 Front vertical zippers
D1.2 Upper zipper
D1.3 Fabric attachment buttons
D1.4 Side support upright openings
D2. Upper frame
D3. Structure/leg support fasteners
D4. Crib structure side upright fasteners
D5. Side tilting button
D6. Crib bottom
D7. Front strap fastening buckle
D8. Rear strap fastening buckle
D9. Mattress stopper
E. Crib structure side uprights
F. Fastening straps
F1. Red crib front fastening buckle
F2. Grey crib rear fastening buckle
F3. Grey bed fastening and height adjustment buckle
G. Mattress with removable lining
H. Bag
ASSEMBLY OF THE CRIB
1. Hold the bottom support "A" and insert the lower bar "B" in the
relevant slot "A8" (Fig.1), pushing the metal pin until you hear
the click. Repeat the same operation for both feet (Fig.1A).
2. Now insert the central support structure "C" into the slots "A7"
on both leg support, pushing the metal pin until you hear
the click (Fig. 2-3).
3. Hold the frame "D2" and turn the upper part of the frame by
90° (Fig.4). Repeat the same operation for the bottom of the
crib "D6" (Fig. 5).
4. Pass the side support uprights "E" through the openings
"D1.4", on both sides of the crib (Fig.6), until they are inserted
into the fasteners "D4", making sure that you have heard the
click of correct installation (Fig.7).
5. Close the vertical front zippers "D1.1" (Fig.8) and then the
upper hinge "D1.2" (Fig.9).
6. Fasten the buttons "D1.3" located in the upper front corners,
and in the front and rear areas of the bottom of the crib
All manuals and user guides at all-guides.com
(Fig.10-11-12).
7. Fasten the crib structure "D" to the legs "A" inserting the
couplers "D3" in the "A9" supports located on both legs
(Fig.13), until you hear the click. Be careful to position the
structure "D" so that the tilting front panel faces in the same
direction as the telescopic feet "A5".
8. Insert the mattress "G" inside the crib structure "D", paying
attention to orient the breathable net surface upwards. Make
sure the mattress rests against the stopper "D9" (Fig.14).
9. Block the 4 wheels "A6" of the crib by lowering the levers that
activate the brakes (Fig.15). The crib is now ready to be used.
ADJUSTING THE CRIB HEIGHT
10. The crib can be adjusted in 11 different heights. To adjust
the height, press the buttons "A1" on the leg support "A" and
lift or lower the structure "D" to the desired position (Fig.16).
Release after hearing the click.
11. The base of the crib can be slightly inclined by adjusting the
leg supports to different heights (Fig.17).
WARNING: The crib can be inclined by a maximum of 4
positions between one leg support and the other (e.g., right leg
support in position 5 and left leg support in position 1 (Fig. 18).
WARNING: The child's head must always be positioned near
the raised end (Fig.19).
WARNING: It is not possible to select different heights on the
two sides of the crib when in rocking configuration.
ROCKING FUNCTION ACTIVATION
12. You can activate the tilting function by pushing down the
buttons "A2" on the leg supports "A" (Fig.20). To deactivate
the function, return the buttons "A2" to their original
position, pushing them upwards.
WARNING: If the crib has been used previously in "Side
sleeping configuration (fastened to the bed), " make sure that
the side is in locked position and check that it is engaged
correctly.
WARNING:
Always remember
configuration when using the product in "Side sleeping
(fastened to the bed)" or when the child is unattended.
WARNING: It is not possible to select different heights on the
two sides of the crib when in rocking function.
SIDE SLEEPING CONFIGURATION (FASTENED TO THE BED)
It is possible to fasten the crib to the parents' bed (side sleeping
configuration).
WARNING - IMPORTANT FOR YOUR CHILD'S SAFETY: This
configuration is allowed only with beds that allow compliancy
with all the conditions described in this paragraph.
In particular, the LOWERED side of the crib must always be
positioned against the mattress of the parents' bed and the
parents' mattress must be aligned with the height of the
crib's side (Fig.21). Moreover, the crib must be fastened to the
structure of the parents' bed or to the mattress support (mesh
or slat sprung base).
WARNING: Check that the structure of the crib in side sleeping
configuration does not interfere with the parents' bed.
WARNING: During use, make sure that the bedsheets, blankets,
etc. do not interfere with the crib's space.
1. Lower the side of the crib by pushing button "D9" and
accompanying the side until it reaches the end of its travel
(Fig.22).
WARNING: Use the crib with the side lowered only in side
sleeping mode, (fastened to the bed).
2. Put the crib against the parents' bed and check its height
compared to the parents' mattress (Fig. 23).
WARNING: The height of the parents' mattress must be higher
than or the same as that of the side of the crib, (fastened to
15
to deactivate rocking