VONROC VC506AC Traducción Del Manual Original página 9

1. Press the power switch (1) into the "OFF/0" posi-
tion and remove the mains plug from the mains.
2. Unlock the locking clamp (7) and remove the
top section (6).
3. Before wet vacuuming, remove the dust collec-
tion bag (26), the HEPA filter (27) and remove all
dirt and debris from the container (8).
4. Carefully slide foam filter (28) down over the filter
cage (15) making sure the whole cage (15) is
covered as shown in Fig. C-2.
5. Reattach the top section (6) again and lock the
locking clamp (7).
6. Insert one end of the hose (17) into the vacuum-
ing port (14). Fully unwind the suction hose (17).
7. Connect the mains plug.
8. Press the power switch (1) into the "ON/I" posi-
tion to start your vacuum cleaner.
9. The machine now is ready for wet vacuum
cleaning.
10. Press the power switch (1) into the "OFF/0" posi-
tion to switch off your vacuum cleaner.
11. Raise the hose (17) so that the liquids drains into
the container (8).
12. Empty the container (8) immediately after suction
cleaning because it is not designed to store
liquids.
Blow function (Fig. A, F, G)
Operation without the use of a filter is
recommended.
Remove all dirt and debris from the
container (8) before you use the blow
function.
Always wear safety goggles before using
the blowing function.
Risk of flying objects. Keep bystanders
away from the work area.
Your vacuum cleaner is equipped with a blowing
function. It can be used to blow dust and debris.
1. Press the power switch (1) into the "OFF/0" posi-
tion and remove the mains plug from the mains.
2. Unlock the locking clamp (7) and remove the top
section (6).
3. Before blowing, remove the dust collection bag
(26), the filter (27, 28) and remove all dirt and
debris from the container (8).
WWW.VONROC.COM
4. Reattach the top section (6) again and lock the
locking clamp (7).
5. Insert one end of the hose (17) into the blowing
port (3) on top of machine. Fully unwind the
suction hose (17).
6. Connect the mains plug.
7. Press the power switch (1) into the "ON/l" posi-
tion to start your vacuum cleaner.
8. The machine is now ready for blowing dust and
debris.
9. Press the power switch (1) into the "OFF/0" posi-
tion to switch off your vacuum cleaner.
Finish operation (Fig. A)
1. Turn off (1) the machine and disconnect the
mains plug.
2. Opening the drainage outlet (12) to allow the
vacuumed liquid to drain out.
3. Close the drain outlet (12).
4. Remove the top section (6) and empty the con-
tainer (8).
5. Clean the machine with a soft cloth.
6. Stow away the mains cable and accessory at
the machine. Store the appliance in a dry room.
5. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and dirt.
Remove very persistent dirt using a soft cloth mois-
tened with soapsuds. Do not use any solvents such
as gasoline, alcohol, ammonia, etc. Chemicals such
as these will damage the synthetic components.
Container
Empty the container (8) immediately after suction
cleaning because it is not designed to store liquids.
1. Opening the drainage outlet (12) to allow the
vacuumed liquid to drain out.
2. Close the drain outlet (12).
3. Remove the top section (6) and empty the con-
tainer (8).
4. Clean the machine with a soft cloth.
EN
9