Publicidad
Device Description:
1. Safety cap
2. Filling hole
5. Indicator light
6. Children lock
Attachments:
A. Funnel ×1
B. Measuring cup × 1
E. Big nozzle x 1
I. Floor brush x 1
J. Connection of floor brush X1
L. Floor brush towel x1
WARNING: − First check an inconspicuous area as to whether the material you intend to clean is suitable for cleaning with a steam
cleaner e.g.:
• Steam could cause lacquered wood or leather to fade.
• Unprotected wood could swell up.
• The steam could remove protective layers of wax.
• Plastics could tint if exposed to steam.
• Soft plastics could deform if exposed to steam.
• Cold glass or mirror surfaces could burst if exposed to hot steam.
− Never fill the steam cleaner with liquids other than water.
− Do not in any case place the steam cleaner or the individual parts in the dishwasher. It would be destroyed.
− Stop using the steam cleaner if its plastic parts exhibit cracks or breaks or are deformed. Only replace damaged parts with
corresponding original spare parts.
− Do not operate the steam cleaner with an empty tank. Once the water reservoir has been used up, pull the mains plug to avoid
overheating it.
− If you would like to clean windows, you must first warm them up, e.g. by applying steam to a larger area at a greater distance and then
from a closer distance.
− Wear gloves, protective goggles, and respiratory protection when attempting to remove substances that are harmful to health.
Before first use:
Remove all packaging materials and stickers off the device. Clean the device with a clean and damp cloth. Open the device by twisting the
safety cap (1) clockwise. Fill with water and pour the water out. This will remove any burrs and factory dirt from inside the device. Then
proceed with normal operation.
Operation:
1. Put the steam cleaner on a dry and flat surface and open the safety cap (1). To do that push the cap firmly downwards and turn the cap
counterclockwise.
2. Use the measuring cup (B) and funnel (A) to fill the device with water. Maximum capacity is 400 ml. We suggest to fill up to 350 ml to get
better performance and more steam production. If there is more than 350 ml in the tank there may be some water in the steam for the first
2 minutes of use.
Special notices:
Please use clean water (small solid particles may block pipe or cause machine failure)
If the tap water in your area is hard or very hard we suggest using a mix of tap water and distilled water.
Please do not add less than 150 ml water.
3. Close the cap rotating it clockwise.
4. Insert the mains plug into the power socket. The red light will light up indicating heating.
5. Once the green light will lights up the device is ready for operation. Please note that the red light will turn on and off during operation.
Please use only once the green light lights up. Otherwise, the device will drip and spray hot water.
6. Turn the child lock (6) to the On position. Then press the steam trigger (7). Steam will be released directly. Remember you should
always keep pressing the steam trigger(7), once you release the steam trigger(7) the Child lock (6) will reset to Off position.
Once finished or the water tank is empty:
If finisher (No steam is generated):
1. Disconnect the device from the mains power.
2. Push the steam trigger (7) and keep it pressed until no more steam is generated.
3. Wait for the device to cool for about 12-20 minutes, depending on the amount of remaining steam inside.
4. Slowly unscrew the safety cap (1) and wait a few minutes for the remaining damp to escape.
If there is no more water in the tank the device will stop generating steam. The water must be refilled. To do that follow the steps below:
1. Disconnect the device from the mains power.
2. Push the steam trigger (7) and keep it pressed until no more steam is generated.
3. Wait for the device to cool for about 12-20 minutes, depending on the amount of remaining steam inside.
4. Slowly unscrew the safety cap (1) and wait a few seconds for the remaining steam to escape.
5. Slowly refill the water tank with water or tap water and distilled water mix. Make sure not to put more than 400 ml.
6. Close the safety cap (1) again.
NOTICE:
The steam cleaner has an overheat protection system. It will automatically switch off if it overheats. Please note that the device might
break if used too many times with the tank empty. Please make sure that during operation there is enough water in the tank at all times.
Accessories description and usage:
D. Flat Brush
Insert the big nozzle into the notch of the flat brush (3C), and turn it clockwise until it clicks (3C). It can clean flat surfaces like windows etc.
After use, take out the flat brush by turn it anti-clockwise.
For cleaning desks and chairs, bookcases, or ironing clothes, put a white towel on the flat brush (3C).
E. Big Nozzle
3. Attachment lock
7. steam trigger
C. Towel set ×1
F. Extension hose× 1
G. Nylon brush x 1
4. Steam outlet
D. Flat brush x 1
H. Stainless brush x 1
K. Extension tube x 3
6
8. Power plug
Publicidad
