Battery Installation; Emptying And Cleaning The Dust Container - Concept VP6200 Manual Del Usuario

EN
OPERATING INSTRUCTIONS
Vacuum cleaner assembly
Always disconnect the plug out of the electrical outlet before assembling or removing accessories!
1. Attach the extension tube (5) into the hand unit of the vacuum (4) until you hear a click sound. To remove the tube
from the hand unit, press the release button (7) and pull away. By pulling the plastic part of the pipe (5), the pipe can
be bent in the joint. When straightening the pipe, you will hear a crack, the pipe will be fixed in a straight position
in the elbow.
2. Attach the turbo nozzle (6) to the extension tube (5), you will hear a click sound. To remove the turbo brush from
the extension tube, press the lock button (7) and pull away.
You can insert the turbo nozzle to the hand unit as described (4).

BATTERY INSTALLATION

Insert the battery (2) into the body of the hand unit (4) and push it lightly. When you hear a click, the battery has been
successfully installed. To release the battery, press the battery release button (3) and pull to remove it.
The battery charging point is located on the bottom of the handle of the hand unit.
Note: To prolong the battery life, always charge the battery when the battery is nearly empty. Do not store or recharge
the appliance in environment with temperatures below 0 °C or higher than 40 °C. These temperatures may damage the
appliance. During the charging process, the temperature of the appliance may increase, this is normal.
While the battery is being charged, the power indicator (D) flashes and remains lit after charging. If both indicators (E, D)
are lit during operation of the vacuum cleaner, the battery is sufficiently charged. If only one indicator is on or flashing,
the battery needs to be charged.
If you do not use the vacuum cleaner for more than 3 months, allow it to charge for 12 hours. Then place the vacuum
cleaner in a dry and cool place.
USE
Before installing the battery, check if it is fully charged.
1. Press the power button (A) located on the handle of the rod part of the vacuum cleaner to switch on the appliance.
2. By pressing the button (B) repeatedly, you can change the power of the vacuum cleaner (3 power levels are
available).
3. After switching the vacuum cleaner on, the 2nd power level is automatically set.
38
4. The current power level is indicated by a light signal (C).
5. At the lowest power, i.e. level 1, signalling (C) is not on. When medium power is switched on, i.e. level 2, the
signalling lights up white, at maximum power, i.e. level 3, the signalling lights up blue.
Note: We recommend to use the maximum power of both the hand unit and the turbo brush in the case of heavily soiled
surfaces or medium-high or high pile carpets.
WET WIPING (MOP)
1. If you also want to mop during vacuuming, place the turbo brush in the water
tank (14) and press lightly, you will hear a click (Fig. 1).
2. Before use, loosen the water tank cap and fill the tank with distilled water (Fig.
2) Observe the maximum water level indicated by the MAX line on the side of
the water tank (Fig. 2).
3. If you want to mop, moisten the cleaning cloth (17) by repeatedly pressing the
water pump on the water tank. We recommend to moisten the cloth before use
to ensure more efficient cleaning.
4. After mopping, pour water out of the tank.
CAUTION! Use only distilled water to fill the water tank!
Always switch off the appliance before filling the water tank with distilled water,
emptying the water tank or replacing the cleaning cloth.
REMOVING AND CLEANING THE CLEANING CLOTH
1. Use the power button to switch off the appliance.
2. Remove the water tank from the turbo brush (6) and then remove the cleaning
cloth.
3. Wash the cloth in the washing machine at a maximum of 40 °C and use a mild
detergent.
Important: Never use bleach or fabric softener to wash the cloth.
ACCESSORIES
Select the accessories according to the nature of the surface to be cleaned.
Water tank with a cleaning cloth – suitable for hard floors
Slot nozzle – suitable for wall corners, car cushioning, radiators, etc.
Nozzle with a brush – suitable for bedding, fabric, sofa, etc.
Hardfloor brush – suitable for hard floors
Wall stand – assembly kit

EMPTYING AND CLEANING THE DUST CONTAINER

1. To empty the dust container (8), first press the dust container release lock (16) and remove the container from the
hand unit (4).
2. Press the dust container lock (9) to open the container, empty the dust, remove the soiled filters from the container
and clean them.
3. Insert cleaned filter back in the dust container and close the lid.
4. Insert the dust container (8) back in the hand unit, you must hear a click.
VP6200 VP6200
EN
Water pump
Fig. 1
Water
MAX
Fig. 2
39