Hapro seecret C200 Instrucciones Originales página 2

ENG
(original instructions)
Introduction
Congratulations on the purchase of your Hapro Seecret® anti-aging appliance! VDL Hapro B.V. produces high quality products made with care
and craftsmanship. The Hapro Seecret® anti-aging appliances meet the same high standards. This new product line has been developed and
assembled in accordance with strictest applicable standards and contains carefully selected, high-quality components. Based on scientifically
demonstrated principles, Hapro Seecret® has been proven to vitalise and improve the healthy appearance of your skin in a relaxing manner.
Before you begin using the appliance, it is recommended that you first read this instructions and the accompanying brochure carefully.
Among other things the documents contains extensive information about the Seecret® anti-aging concept, it's influence on the skin and the
use of the appliance. With this information you will enjoy years of pleasure from your Hapro Seecret® anti-aging appliance.
Important
● We request you when opening the packaging to always check the product for external defects, imperfections or transport damage.
Should it regrettably display defects or omissions, please contact your dealer.
● Check if the voltage indicated on the appliance corresponds to the mains voltage in your home before you connect the appliance.
● If the supply cord is damaged, it must be replaced by the manufacturer or service agent or a similarly qualified person in order to
avoid a hazard.
● Water and electricity are a dangerous combination! Do not use this appliance in wet surroundings (e.g. in the bathroom or near a
shower or swimming pool).
● If you have just been swimming or have just taken a shower, dry yourself thoroughly before using the appliance.
● Children should be supervised to ensure that they do not play with the appliance.
● The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction.
● Always unplug the appliance after use.
● Let the appliance cool down for approx. 15 minutes before storing it.
● Make sure the vents of the appliance remain open during use.
● Colours may fade under the influence of the sun. The same effect may occur when using this appliance.
● Protect your eyes during session using the goggles provided. Contact lenses and sun glasses are not a substitute for the goggles.
● Do not use the appliance if the timer is defective.
Using the appliance
When your appliance is properly installed and functions properly it is ready for use.
Session
As with all safe and painless skin stimulation methods, a single session will not immediately improve the skin. Aging of the skin is a process
that takes place over many years, so it should be no surprise that it cannot be reversed with just one session lasting several minutes. To
achieve the desired effects and see visible results a series of rejuvenation sessions is required. We recommend that you indulge in 2-3
rejuvenation sessions per week over a period of 10 to 12 weeks. Keep in mind that a 48-hour rest period is required before you begin the next
session.
The results will be measurable after about one month, and you will see visible results after about three months. This differs from person to
person, however, and depends greatly on the skin. After three months it may be assumed that the condition of your skin has reached a level at
which the frequency of the sessions can be reduced. You can then switch to 'maintenance sessions' , once every two weeks.
Session time Number of sessions per week
20 minutes 2-3
● A course of treatment during a continuous 10 to 12 week period
● 2 to 3 sessions per week
● Rest period of 48 hours between sessions
● A maintenance session once every two weeks, after completing a course of treatment
As far as is known, from a scientific perspective, there is no need to limit the number of treatments with collagen light. However, based on
careful study and practical tests, VDL Hapro B.V. has established these usage recommendations to help you achieve the most optimal results.
Protective goggles
The protective goggles should only be used with a Hapro Seecret appliance. They should not be used for other purposes.
The protective goggles comply with protection class II according to directive 89/686/EEC.
Number of weeks
10-12
- 2 -