Chicco next2me Dream EVO Manual Del Usuario página 15

uct must be carried out by an adult.
• Do not use the product without the
frame.
• Keep the fastening straps out of
reach of children.
• Infants can suffocate on soft bed-
ding. Avoid placing pillows or simi-
lar items under newborn babies for
additional comfort during sleep.
• Use the crib in "Bedside sleeper
Con figuration (fastened to the bed)"
only with beds of the size indicted
in the reference figure at the begin-
ning of the manual.
• Do not leave anything inside the
product that might reduce its depth.
• To prevent the child from being
trapped, do not place the crib close
to walls or obstacles.
• Do not leave any small objects
inside the product that might be
swallowed.
• Do not make adjustments to the
product when the child is in it.
• Do not move the product when the
child is inside.
• Do not use the product with more
than one child at a time.
• Prolonged exposure to direct sun-
light may cause the products colour
to fade. After prolonged exposure of
the product to high temperatures,
wait a few minutes prior to putting
your child in it.
• WARNING: Be careful when the child
is in the crib, that objects or bedding
items do not fall into the crib.
• Keep the product out of reach of
children when it is not in use.
COMPONENTS
A. Leg rest with wheels
A1. Height adjustment button
A2. Height indicator
A3. Telescopic foot release button
A4. Telescopic feet
A5. Wheels with brakes
A6. Bottom bar slots
A7. Housing for top part of the crib
B. Bottom bar
C. Crib structure
C1. Fabric
C1.1. Front vertical zippers
C1.2. Upper hinge
C1.3. Fabric attachment buttons
C2. Structure/leg support fasteners
C2.1. Buttons for attaching/releasing the top structure
C2.2 Lever for attaching/releasing the bottom structure
C3. Side panel opening button
C4. Top tube
C5. Crib bottom
C6. Front strap fastening buckle
C7. Rear strap fastening buckle
C8. Mattress stopper
D. Fastening straps
D1. Red crib front fastening buckle
D2. Grey crib rear fastening buckle
D3. Grey bed fastening and height adjustment buckle
E. Mattress with removable lining
F. Bag
ASSEMBLY OF THE CRIB
1. Hold the bottom support A and insert the lower bar B in the
appropriate slot A6 (Fig.1), pushing the metal pin until you
hear the click. Repeat the same operation for both feet (Fig. 2).
2. Hold the top tube C4 and have it rotate by 90° (Fig. 3). Repeat
the same operation for the bottom of the crib C5 (Fig. 4).
3. Close the vertical front zippers C1.1 (Fig.5) and then the up-
per hinge C1.2 (Fig.6).
4. Fasten the buttons C1.3 located in the upper front corners,
and in the front and rear areas of the bottom of the crib
(Fig.7-8-9).
5. Fasten the crib structure C to the legs A inserting the cou-
plers C2 in the A7 supports located on both legs (Fig.10-11).
Be careful to position the structure C so that the tilting front
panel faces in the same direction as the telescopic feet A4.
6. Place the mattress E in the crib C. Make sure the mattress
rests against the stopper C8 (Fig.12).
7. Block the 4 wheels A5 of the crib by lowering the levers that
activate the brakes (Fig.13). The crib is now ready to be used.
ADJUSTING THE CRIB HEIGHT
The height of the crib can be adjusted in 11 different positions.
To adjust the height, press the buttons A1 on the leg support A
and lift or lower the structure C to the desired position (Fig.14).
Release after hearing the click.
The base of the crib can be slightly inclined by adjusting the 2
leg supports to different heights (fig.15).
WARNING: The crib can be inclined by a maximum of 4 po-
sitions between one leg support and the other (e.g., right leg
support in position 5 and left leg support in position 1) (Fig. 16).
WARNING: The child's head must always be positioned near
the raised end (fig.17).
SIDE SLEEPING CONFIGURATION (FASTENING THE CRIB
TO THE BED)
The crib can be fastened to the parents' bed (side sleeping con-
figuration).
WARNING - IMPORTANT FOR YOUR CHILD'S SAFETY: This
15