Ferguson ARIVA T30 Manual De Uso página 11

EN
4. Sleep Mode - If this setting is disabled,
this feature does not work. If this set-
ting is enabled, a message will appear
after the preferred time letting you
know that the device will enter sleep
mode. The auto power off function can
be set between 0-12 hours. The stand-
ard setting is 3 hours. Press the STAND-
BY button to exit Sleep/Auto Off mode.
9. Options
To access the menu, press MENU and se-
lect [Options]. The menu provides options
to adjust the OSD language, subtitle lan-
guage and audio language. Select an op-
tion and press RIGHT/LEFT to adjust the
setting. Press EXIT to exit the Menu.
1. OSD Language - Select the language of
the OSD.
2. Audio language - Select the preferred
audio language for watching TV chan-
nels. If the language is not available, the
default language of the program will be
used.
3. Subtitle Language - Select your pre-
ferred subtitle language.
4. Digital Audio - Select the digital audio
output mode.
10. System settings
To enter the Menu, press MENU and select
[System]. The menu provides options for
adjusting system settings. Press UP/DOWN
to select an option and press RIGHT/LEFT
to adjust the setting. Press EXIT to exit the
Menu.
1. Parental supervision - You can restrict
access to channels that are unsuitable
for children. To restrict/lock a channel,
you need to enter a password. The de-
fault password is "000000".
2. Set password - Set or change a pass-
word for blocked programs. Enter
your old password or the default pass-
word "000000". After that, you will be
prompted to enter a new password. To
confirm, re-enter the new password.
After confirming, press EXIT to exit the
menu.
3. Restore factory default settings - Reset
the decoder to factory default settings.
In the main menu, select [Restore fac-
tory settings] and press OK or RIGHT to
select. Enter your password or the de-
fault password "000000" and press OK
to confirm. This option will delete all
preset channels and settings.
4. Information - View information about
the model, hardware and software.
5. Firmware Upgrade - If the status is set
to "ON", the receiver will automatically
check for software upgrades.
11. USB
To access the Menu, press the MENU but-
ton and select [USB]. The menu provides
options for playing music and photos. The
receiver supports MP3, WMA, JPG, BMP
files. The receiver only supports USB de-
vices with the FAT and FAT32 file system. It
does not support the NTFS file system.
1. Multimedia - If no USB device is con-
nected, a warning message "USB device
not found" will appear, otherwise you
can select music or photos and press
OK to go to the file browser and select
the file to play.
2. Configure the display of photos
• Slide time: set the slideshow interval
to 1-8 seconds.
• Slide mode: Set the slide show effect.
• Aspect Ratio: Keep original picture
aspect. [Discard] displays the image
in full screen mode.
3. Configure the display of movies
• Aspect Ratio:
[Keep]: Play back the movie in its
original aspect ratio.
[Discard]: Play the movie in full
screen mode.
• Subtitles:
[Small]: Display the subtitles in the
small mode.
[Normal]: Display subtitles in normal
mode.
[Large]: Displays the subtitles in large
mode.
• Subtitles background:
[White]: Display the subtitles with
a white background.
[Transparent]: Display the subtitles
with a transparent background.
[Gray]: Display the subtitles with
a gray background.
[Yellow-green]: Display subtitles in
yellow-green background.
• Subtitle font color:
[Red]: Displays the subtitles in red.
[Blue]: Displays subtitles in blue.
[Green]: Display subtitles in green.
Attention!
• We cannot guarantee the compati-
bility (operation and/or power sup-
ply) with all USB storage devices and
are not responsible for any data loss
that may occur when connected to
this device.
• The system may take a long time to
read the contents of the USB device
when the amount of data is large.
• Some USB devices may not be recog-
nized properly.
• Even if they are in a supported for-
mat, some files may not be played
back or displayed depending on the
content.
4. PVR configuration
[Recorder]: Select a disk for saving re-
cordings.
[Format]: Format the selected disk.
EN