Eicon Networks Diva 2440 Guía Rápida De Instalación página 7

LAN Setup Guidelines
Installing the Diva 2440 on an existing LAN can be extremely
simple or quite challenging, depending on the complexity of your
existing LAN setup. This section provides important points to keep
in mind when installing the Diva 2440 on a LAN.
ADSL
Cable
About the Ethernet Cable
The yellow cable included with your package is a crossover cable
and is used for connecting the Diva 2440 directly to a computer. To
connect the Diva 2440 to a network hub, you need to use the
included straight-through Ethernet cable (this cable may be blue
or grey).
However, the yellow cable can be used if your hub has an uplink
port. Consult the documentation included with your hub for further
information.
General Setup Procedure
The following is a general guideline for the setup procedure you
must follow when setting up the device on a LAN.
Connect the Diva 2440 to the hub on your LAN.
1.
Contact the Diva 2440 using a computer on your LAN as
2.
described in 'Step 2: Enter Account Information' on page 4. If
you are using Windows, this is more easily done with the Diva
Assistant (see 'Built-in DHCP Server' below).
If you cannot contact the device over a LAN, use a single
Note:
non-networked computer for initial configuration.
Complete the Internet Wizard as described in 'Step 3: Complete
3.
the Internet Wizard' on page 5, then verify that the Internet is
accessible from the required machines.
Adjust other LAN settings, such as those on a router or on the
4.
Diva 2440 itself.
Ethernet
Cable
Hub
Built-in DHCP Server
The Diva 2440 has a built-in DHCP server. When you drop the
Diva 2440 into a LAN, the Diva 2440 senses if another DHCP server
exists and de-activates its own DHCP services. To re-activate the
DHCP server, disable the other server, then press the Reset button.
Using the Diva Assistant to set up on a LAN
The default LAN IP address for the Diva 2440 is 192.168.1.1.
Normally, in order to contact the Diva 2440 through TCP/IP, your
computer's IP address must be on the same subnet as the device.
For example, your computer could be set to 192.168.1.2.
If at least once computer on your LAN uses Windows, install the
Diva Assistant on that computer and use it to contact and configure
the Diva 2440. The Network Wizard, a feature of the Diva Assistant,
will contact the Diva 2440 over a network, without having to
change the computer's TCP/IP settings.
To use the Network Wizard, right-click on the Diva Assistant icon in
Power the system tray and select 'Network Wizard'. Once the Diva
Adapter
Assistant has discovered the Diva 2440, you will be asked if you
want to change its IP address.
IP Addressing
If your LAN uses static IP addressing, or if you are using an
existing DHCP server, you must assign the Diva 2440 a unique IP
address. To change this setting, access the web interface, click
'Advanced Configuration', click 'System Settings', enter a new IP
address in the 'LAN IP Address' field, then click 'Save'.
This step is done automatically if the Diva Assistant is used.
Note:
Once you click 'Save', you will lose contact with the device. To
access the web interface, click the 'File' menu in your web browser,
then click 'Open', then enter the new IP address. You may need to
change the TCP/IP settings on your computer before being able to
access the Diva 2440 after the IP address has been changed.
However, if your computer is set to acquire its IP address
dynamically from a DHCP server, you need only restart your
computer (or reset the IP address manually using 'winipcfg' with
Windows 9x or 'ipconfig /renew' for Windows 2000/NT). The
Diva 2440 will assign the new address.
LAN IP
address
7