Publicidad
Idiomas disponibles
Idiomas disponibles
GENERAL INSTRUCTIONS.-
Carefully read through the instructions contained in this
manual. It provides you with important informa- tion
about assembly, safety and use of the machine.
1
This unit has been designed for professional use. The
weight of the user must not exceed 150kg.
2
Keep your hands well away from any of the moving
parts.
3
Parents and/or those responsible for children should
always take their curious nature into account and how
this can often lead to hazardous situations and be-
haviour resulting in accidents. This unit does not have
to be used in any case like toy.
4
The owner is responsible for ensuring that anyone
who uses the machine is duly informed about the
necessary precautions.
5
Your unit can only be used by one person at a time.
6
Use suitable clothing and footwear. tie up your
shoelace correctly
1.-
ASSEMBLY INSTRUCTIONS.-
Take out all of the assembly pieces and remove the
packing. Check that all of the assembly pieces are
present, Fig.1.
ATTENTION: The assistance of a second person is
recommended when assembling this machine.
Fig.1 Parts list:
(1) Main body.
(2) Rail
(51L) Left swing post.
(51R) Right swing post.
(59) Bushing.
(61L) left pedal tube.
(61R) right pedal tube.
(63L) Left pedal.
(63R) Right pedal.
(71) Console.
(135) Adaptor.
(414) End cap.
(415) Bushing.
(610) End cap.
Fig.2 Fasteneers List:
(52) Nut UNF
(54) Washer D4
(66) Washer D6
(410) Washer D8
(16) Screw M10x16
(17) Screw M10x65
(67) Screw M6x40
(69) Screw M8x12
(416) Screw M8x50
(417) Nut M8
Wrenches.
2. FITTING THE MAIN BODY.-
ATTENTION: The assistance of a second person is
required for this stage of the assembly.
Assembly the main body (1) onto rail base (2),
positioning according to the figure, Fig.3, insert screws
(16) and (17) and tighten slightly.
Align the structure and securely tighten.
Release the arms (41R) and (41L) and fit them over
the rail (2). Place caps (415) and tighten the screws
(416) and nuts (417). Fig.4.
3. FITTING THE UPPER FOCUS BARS.-
Take the left arm (51L) (marked with the letter L) and
insert it onto the focus bar spindle, Fig.5. Fit the nuts
(52) and washers (54) and tighten securely.
Take the right focus bar (8), (marked with the letter "R")
and go through the same assembly procedure as with
the left.
Place the end caps (414).
4. FITTING THE FOOT REST
Place the left footrest (63L) marked with the letter (L)
on the left pedal tube (61L) and tighten the screws (67)
and washers (66). Perform the same assembly with the
right footrest. Fig.6.
5. FITTING THE FOOT REST FOCUS BARS.-
Place the bushing (59) and then the left pedal tube
(61L) on the shaft of the left arm (51L). Strongly tighten
the screws (69) and washers (69). Place the cap (610)
Fig.7.
Put the pedal tube (61L) on the tube (41L) aligning the
two holes, Fig. 8. Insert the screw (64) with the nut (65)
and tighten securely.
Perform the same assembly with the right side tube
(61R).
6.- FITTING THE MONITOR.-
Take hold of the monitor (71) and bring it up to main
post (11), connect the terminals (9PIN; 2PIN), coming
out of the bottom of the monitor, with terminals (133)
and (13) coming up out of the top of the main post (11),
Fig.9.
Attach the monitor (71) using screws (72), Fig.9,
making sure not to pinch the wires.
IMPORTANT: It is advisable to retighten these
screws after one month of using the machine.
LEVELLING.-
Once the unit has been placed into its final position,
make sure that it sits flat on the floor and that it is level.
This can be achieved by screwing the adjustable feet
(23) (25) up or down, as shown in Fig.10.
10
G889
.-
Publicidad
