Publicidad
ENGLISH
Battery Installation
Your
RCR503BR
universal remote requires 2 new AAA alkaline batteries (sold
separately).
To install the batteries:
1. Turn the unit over, and remove the battery compartment cover.
2. Insert the batteries, matching the batteries to the (+) and (-) marks inside
the battery case.
Battery Precautions:
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or rechargable (nickel-cadmium) batteries.
• Always remove old, weak or worn-out batteries promptly and recycle or dispose of them in accordance
with Local and National Regulations.
Programming with Direct Entry
To program your remote to control up to three
components, follow these steps:
1. Manually turn on the component you wish
to program the remote to operate.
2. Find the four-digit code for your brand of TV,
VCR, DVD, satellite receiver, cable box, or
digital TV converter in the enclosed code lists.
SAT•CBL• DTC VCR•DVD
3. Press and hold the
CODE SEARCH
key until the indicator light turns on.
4. Release the
CODE SEARCH
key.
5. Press and release the
TV, VCR·DVD
or
SAT•CBL•DTC
key. The indicator light
blinks and then remains lit.
Note: DTC refers to digital TV converter.
6. Enter the four-digit code, using the numeric
keypad. After the code is entered, the
indicator light turns off.
Note: If the indicator light blinks multiple times, you've
entered an invalid code. Start from step 2 again.
7. Aim the remote at the component and
press the
ON•OFF
key. The component
should turn off.
Note: If your component does not respond, try all the
codes for your brands. If the codes do not work or
your brand is not listed, try the Code Search Method
that follows.
Programming With Code Search
If your TV, VCR, DVD, satellite receiver, cable box, or digital TV converter does
not respond after you have tried all the codes for your brands, or if your brand
is not listed, try searching for your code via the Code Search Entry Method. To
program your remote via the Code Search Entry Method, follow these steps:
1. Manually turn on the component you wish
to program the remote to operate.
2. Press and hold the
CODE SEARCH
key
until the indicator light turns on.
3. Release the
CODE SEARCH
key.
ENGLISH
2
Programming With Code Search Continued
4. Press and release the component key you
wish the remote to control—
SAT•CBL•DTC
key. The indicator light blinks
once and remains lit.
Important: Find the ENTER key on your remote (don't
press it yet). You will need to press this key quickly in
step 6 below.
5. Press and release the ON•OFF key until the
component turns off.
Important: You may have to press the ON•OFF key up
to 200 times.
6. As soon as the component turns off, press
the ENTER key within 4 seconds. The indi-
cator light turns off.
Note: If you wait longer than 4 seconds to press ENTER,
the remote goes to the next code—you will need to start
the code search from step 1 again.
Menu Function – TV, SAT•CBL•DTC, VCR•DVD
The Menu function on your remote is used to make changes on selected settings.
INDICATOR
The
MENU
key operates in TV, DBS and DVD Modes. Each menu varies from
LIGHT
brand to brand.
The TV Menu is used to make changes in the TV settings, such as changing color,
channels and timers.
to make changes to settings. The VCR or DVD Menu you can navigate to languages,
subtitles and more.
(BLINK)
TV
While in Menu Mode, these keys function as follows:
Mode
TV, SAT•CBL•DTC,
VCR•DVD
To use the Menu function, follow these steps:
1. Press the component button whose menu
you wish to access (
SAT•CBL•DTC
).
2. Press the
MENU
(OFF)
component is shown.
Note: Some functions of some brands may not be fully
supported.
ON•OFF
3. To exit the menu mode press the corresponding
component key on the remote (
SAT•CBL•DTC
).
Special Notes for Menu Use
1. In the Menu Mode of RCA, GE and PROSCAN TVs, pressing the
selects the highlighted item. The numeric keys may also be used to select the
menu choice.
2. For SONY components, pressing the
to the previous menu.
Accessing Digital Channels
The INPUT and — (dash) key lets you enter a digital sub-channel number, like 59.1,
INDICATOR
directly. Use the number keys to enter the main channel number (in this case, "59").
LIGHT
Then press the INPUT (–) key and press the subchannel number (in this case, "1"). The
INPUT key has two other functions as well: (1) it toggles through all the video sources
connected to your TV; and (2) when the remote is in VCR mode, this button toggles
between VCR and the TV input.
ENGLISH
SAT•CBL• DTC VCR•DVD
TV
TV, VCR·DVD
or
ON•OFF
The SAT•CBL•DTC Menu navigates through the Menu screens
Vol up/ down
Ch +/-
Cursor moves right/left
Cursor moves up/down
SAT•CBL• DTC VCR•DVD
TV, VCR·DVD
or
key. The menu of the chosen
SAT•CBL• DTC VCR•DVD
TV, VCR·DVD
or
MENU
ENTER
key while in Menu Mode returns
3
Care and Maintenance
• Keep the remote dry. If it gets wet, wipe it dry immediately.
(BLINK)
• Use and store the remote only in normal temperature environments.
• Handle the remote gently and carefully. Don't drop it.
•
Keep the remote away from dust and dirt.
• Wipe the remote with a damp cloth occasionally to keep it looking new.
• Modifying or tampering with the remote's internal components can cause malfunction
and invalidate its warranty.
90 Day Limited Warranty
(OFF)
VOXX Accessories Corporation warrants that for 90 days from date of purchase, it
will replace this product if found to be defective in materials or workmanship. Return
it to the address below for a replacement with a current equivalent. This replacement is
the company's sole obligation under this warranty. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE IS DISCLAIMED.
This warranty excludes defects or damage due to misuse, abuse, or neglect. Incidental or
consequential damages are disclaimed where permitted by law. This warranty does not cover
product purchased, serviced or used outside the United States or Canada.
U.S.A.: Audiovox Return Center, 150 Marcus Blvd., Hauppauge, New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
ESPAÑOL
Instalación de las Baterías
TV
Su control remoto universal RCR503BR requiere de 2 baterías alcalinas AAA nuevas
(se venden por separado). Para instalar las baterías:
1. Voltee la unidad, y quite la tapa del compartimiento de baterías.
2. Introduzca las baterías, cuidando que el (+) y el (-) de las baterías sean iguales a las
marcas dentro del compartimiento de las baterías.
Precauciones sobre las baterías:
• No combine baterías nuevas y viejas.
• No combine diferentes tipos de baterías: alcali-
nas, estándar (carbón-zinc) o recargables (níquel-
TV
cadmio).
Programando con Entrada Directa
key
Para programar hasta 3 componentes en su control remoto, siga los siguientes pasos:
1. Encienda manualmente el componente que usted desea programar en el control
remoto.
2. Localice el código de cuatro dígitos para la marca de su TV, VCR, DVD, receptor
de satélite o caja para el cable en la lista
de códigos anexa.
3. Presione y sostenga la tecla
CODE SEARCH
que se ilumine el indicador.
4. Luego suelte la tecla
CODE SEARCH
ENGLISH/ESPAÑOL
• Siempre remueva de inmediato baterías viejas,
débiles o desgastadas, y recíclelas o deséchelas
según lo disponen las normas locales y nacionales.
(búsqueda de códigos) hasta
.
4
5
6
7
E
Publicidad
