MODEL: PST9040Q
●
Use only a pressure-regulated compressed
air source to limit the air pressure supplied to
the tool. The regulated pressure must not
exceed 110psi. If the regulator fails, the pressure
delivered to the tool must not exceed 200psi.
Over pressurizing the tool is able to result in
bursting, abnormal operation, breakage of the
tool or serious injury to persons. Use only clean,
dry, regulated compressed air at the rated
pressure or within the rated pressure range as
marked on the tool. Always verify prior to using
the tool that the air source has been adjusted to
the rated air pressure or within the rated air-
pressure range.
●
Always disconnect air source:
◆Before unloading or making adjustments.
◆When maintaining the tool.
◆When clearing a jam.
◆When touching the safety yoke.
◆When tool is not in use.
◆When moving to a different work area.
Such precautionary measures reduce the risk of
injury to persons.
LOADING TOOL
●
Do not load the tool with fasteners when any
one of the operating controls is activated.
Never place a hand or any part of body in
●
fastener discharge area of tool.
Never point tool at anyone.
●
●
Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
!
WARNING:
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
06
HTTP://WWW FREEMANTOOLS COM
.
UNPACKING
●
This tool has been shipped completely
assembled.
●
Carefully remove the tool and any
accessories from the box.
Inspect the tool carefully to make sure no
●
breakage or damage occurred during
shipping.
●
Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
●
If any parts are damaged or missing, please
call
1-888-669-5672
.
!
WARNING:
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
!
WARNING:
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result
in hazardous condition leading to
possible serious personal injury.
1-888-669-5672
.
MODEL: PST9040Q
FEATURES
SPECIFICATIONS
REQUIRES:
5.87 SCFM with 100
fasteners per minute @ 90 psi
AIR INLET:
1/4 inch NPT
MAGAZINE CAPACITY:
100 fasteners, 18 gauge
2.79 lbs
WEIGHT:
MAXIMUM PRESSURE:
110 psi
60 psi 110 psi
-
PRESSURE RANGE:
PIN SIZE RANGE: 1/2 inch to 1 5/8 inch
-
1/4"(5.7mm)
1/2"
13mm
5/8"
16mm
3/4"
19mm
1"
25mm
1-1/4"
32mm
1-1/2"
38mm
1-5/8"
40mm
Compatible with
All Generic 18 Gauge 1/4"
Crown Staples from 1/2" to 1-5/8".
FEATURES
°
●
360 ADJUSTABLE EXHAUST
Allows user to direct air away from
f
face
.
●
OIL-FREE DESIGN
For less maintenance.
ANODIZED ALUMINUM CYLINDER AND
●
MAGAZINE
For long lasting durability.
●
COMFORT-GRIP HANDLE
For increased comfort and control.
●
ERGONOMICALLY ENGINEERED BODY
Rugged and Comfortable resulting in a light-
weight tool great for extended use.
AIR FILTER
●
Keeps interior components debris free, extending
tool life.
ADJUSTABLE DEPTH
●
Depth is easily adjustable for various
applications.
QUICK-JAM RELEASE
●
Allows for easy access clearing in the event of a
jam.
NON-MARRING SAFETY CONTACT
●
Eliminates damage to working surface.
HTTP://WWW FREEMANTOOLS COM
.
OPERATION
USING THE BELT HOOK
The tool is packed with a separate hook system.
Assemble the hook on the tool before using the
hook. The hook can be positioned on both left and
right sides.
⒈
Loosen and remove the hook screw and nut(A).
Save the screw and nut for future use.
⒉
Position the hook in your preferred position.
Using the longer screw packed with hook, fasten
hook to tool.
Hook nut (A)
Hook
1-888-669-5672
.
07