Electrical Connection; Shutting Down; Routine Maintenance - Tecomec Easy Rivet Manual De Instrucciones

16. WARNINGS ABOUT THE TOOLS
- Use the correct inserts and spinner tools depending on the
type of chain to be riveted.
- Do not force an insert into the bush. Do not use tools that
do not fit perfectly in place.
- Use exclusively clean and undamaged inserts and spinner
tools.
- Make sure the size of the inserts and spinner tools are
identical (A-A e B-B).
17. CHECKING THE TOOLS
Visually make sure the insert and spinner tool are not
chipped. Do not use them if they are!
18. TOOL ASSEMBLY (FIG.6)
- Insert the insert U1 into the operating screw tip B1.
- Insert the tool U2 into the bush B2.
- Screw the wheel into the hole F2.
Make very sure the end of the insert fits into the
hole.
Use inserts and spinner tools that are identical
in size, checking the reference etched on the
actual tools.

19. ELECTRICAL CONNECTION

- Make sure the electrical system power supply complies
with the values written on the rating nameplate.
- The power supply voltage must not differ from that written
on the nameplate by ±5%.
- The connection to the electric mains must be prepared
subject to current standards in force in the country in which
the machine is used.
- The power socket used for the machine must have an earth
wire, adequate fuse and must be protected by a differential
circuit breaker with tripping sensitivity no higher than 30
mA.
20. START-UP
- Plug the power cable into the mains.
21. RIVET SPINNING WARNINGS
- Wear personal protection equipment when
sharpening.
- All adjustments must be made with the motor
switched off and the rivet spinner completely stop-
ped.
- In the case of accidental impact or knocks against
the tools during the rivet spinning process, follow
the instructions given in the "WARNINGS ABOUT
THE TOOLS" section.
- Whenever you need to replace the tools, follow the instruc-
tions given in the "WARNINGS ABOUT THE TOOLS"
section.
- Before putting the chain in position, start the rivet spinner
and make sure the insert turns without oscillating.
- You are recommended to clean the chain before rivet
spinning it.
EN
22. RIVET SPINNING THE CHAIN
- Manually assemble the two ends of the chain using the
appropriate connection links.
- Position the chain on the two chain guide discs G2 (fig.7).
The head of the rivet to be spun must face the tool U2.
- Adjust the position of the two chain guide discs G2, by
turning the winged screws V1 (fig.8), so that the rivet is
at the same height as the tools U1 and U2, as illustrated
in the detail.
- If necessary, run the chain over the chain guides (fig.9),
so that the rivet is perfectly aligned with the tools U1 and
U2 (as shown in the detail).
- Turn the wheel V5 so that the rivet sits against the insert
U1 (fig.9).
- Put a few drops of oil on the rivet (fig.10).
- Turn the machine on using switch I2 (fig.10).
- Leave the machine running for 3-4 seconds, before turning
the wheel V5.
- Turn the wheel progressively (without forcing it) V5 (fig.10).
The end of the rivet spun should appear the same as that
on the opposite side.
- Do not force the wheel V5 excessively to avoid
touching and damaging the pulling links.
- Stop the machine, loosen the wheel V5 and repeat the
spinning process for the second rivet of the connection
link.
- Upon completion, stop the machine and check the
chain.
Get hold of the links next to the connection link just spun
and make sure they turn freely on the rivets without any
axial play.
23. STOPPING AND SHUTTING DOWN
23.1 STOPPING
Turn the machine off by turning the switch to position "0" and
unplug the power cable from the mains.

23.2 SHUTTING DOWN

Once you have finished using the machine, disconnect it
and clean it thoroughly.
Store it in a dry and safe place, protected against dust and
damp.

23.3 ROUTINE MAINTENANCE

Follow the instructions given in the "STOPPING"
section before you start to work on the machine.
Maintenance
frequency
40 hours
Operation
Clean the rivet spinner
thoroughly using a rag or
wire brush cleaner.
L u b r i c a t e t h e t h r u s t
bearing.
7