General Maintenance; Cleaning The Boiler - POLTI vaporella SILENCE FRIENDLY_8.85 Manual De Instrucciones

6. OUT OF WATER
The water level is always visible thanks to the transparent tank
(10).
When the water in the tank has been used up, a prolonged noise
will be heard from the self-filling system pump and the steam
will stop flowing. To resume use, simply:
- switch off and disconnect the Vaporella.
- fill the tank as described in Chapter 1.
- connect and turn the Vaporella back on.
WARNING: This operation must always be done after having
disconnected the appliance from the mains.

7. GENERAL MAINTENANCE

Before carrying out any maintenance on the device, always
unplug it from the power mains making sure that the product
has cooled down before proceeding.
To clean the outside of the appliance, only use a damp cloth.
Do not use detergents of any type.
For good maintenance of the boiler we suggest using Kalstop,
the special natural-base limescale, distributed by Polti, and
available for sale at all major domestic-appliance stores or
online at www.polti.com.
Clean the iron soleplate when it is completely cold with a damp
cloth or with a non-abrasive sponge.
8. KALSTOP
Kalstop is the limescale product for appliances with boiler for
ironing and steam cleaning.
Regular use of Kalstop, every time the tank is filled with water:
- Extends the life of the appliance.
- Allows emission of a "drier" steam
- Prevents limescale build up.
- Protects the walls of the boiler.
- Contributes to saving energy.
HOW TO USE KALSTOP
8.1 Dilute one phial in 5 litres of water before putting it in the
tank.
8.2 Fill the tank as described in Chapter 1.
8.3 Start ironing the garments.
EXTRAORDINARY MAINTENANCE WITH KALSTOP
When the boiler has heavy limescale build-up, leave just 250
ml of water in the boiler, add 3 doses of Kalstop, pressurize the
boiler and press the steam control button until the steam stops.
Turn off the appliance, wait at least 2h until it is completely cool,
rinse the boiler repeatedly to remove all limescale residue. After
cleaning the boiler, proceed normally.
For operations with access to the boiler, please refer to the
safety warnings and instructions listed in Chapter 9.
Kalstop is sold in packages of 20 phials at household appliance
stores, at Polti authorized service centres and at www.polti.com.

9. CLEANING THE BOILER

(extraordinary maintenance)
WARNING: Steam.
Risk of scalding!
WARNING: Risk of scalding! When accessing the boiler
(removing the cap, filling up, emptying), ensure that the
appliance is switched off at the power switch and
disconnected from the mains for at least two hours.
To maintain optimum performance, clean the boiler every 10/20
uses depending on the amount of limestone in the water.
9.1 Unplug the appliance and let it cool down for 2 hours at least,
if it is hot.
9.2 Empty the water tank to prevent leakage.
9.3 Turn the appliance over and unscrew the boiler cleaning cap
(11) located on the bottom of the appliance.
9.4 Pour 250 ml of cold water (12) into the boiler using the
funnel supplied.
WARNING: Do not
recommended and pour it slowly into the boiler, paying
attention not to let it overflow.
9.5 Rinse the boiler and pour the water into the sink or into a
special container. If the water is very dirty, repeat the operation
until it is clean.
9.6 Put 100 ml of water in the boiler and screw back the cap.
Make sure that the seal is in and the cap is screwed on properly.
9.7 Fill the water tank again.
9.8 Turn the appliance on again.
Before ironing, dispense steam into a sink or other container
making sure that it is clean. This should take a few seconds.
9.9 Resume ironing normally.
10. STORAGE
10.1 Turn off the appliance and disconnect from the mains
electricity.
10.2 Wait for the appliance to cool down completely before
storing it.
10.3 Empty the water tank.
10.4 Position the monotube and the power supply cable in the
special housings located on the sides of the appliance (13)-(14).
10.5 Replace the Vaporella, using the carrying handle (15)-(16).
WARNING: Before moving Vaporella with the handle, make
sure that the power supply cable and monotube have been
stored as described in Point 10.4.
| 23 |
exceed the quantity of water