Safety Instructions - Truper SOT-225 Instructivo

SAVE THIS INSTRUCTION MANUAL
You will need this manual in order to check safety and caution
rules, assembly instructions, operating and maintenance
procedures, parts list and diagram.
Keep your invoice with this manual. Fill in the invoice number
in the inner side of the front cover. Keep the manual and
invoice in a safe and dry place for future reference.

SAFETY INSTRUCTIONS

NOTE: When using tools, basic safety precautions
should always be followed to avoid risk of personal
injury as well as damaging the equipment.
Read all the instructions before using any tool.
1. Keep your work area tidy. Cluttered areas and benches
invite injuries.
2. Consider work area environment. Do not use
machines or power tools in damp or wet locations.
Do not expose power tools to rain. Keep work area
well lit.
Do not use power tools where flammable liquids or
gases are present.
3. Guard against electric shock.
Prevent body contact with grounded surfaces such
aspipes, radiators or refrigerators.
4. Keep children away. Children shall never be near work
area.
Children are not permitted to hold machinery, tools or
extension cables.
Visitors are not allowed to handle tools; they should be
kept away from work area.
5. Store the equipment while not in use. When not in use,
tools should be stored in dry and dust free shelves,
padlocked and out of children's reach.
6. Do not force tool. It will do the job better and safer at the
rate for which it was intended.
Do not use inadequate attachments to exceed the tool's
capacity.
7. Use the right power tool. Do not force small tools to do
heavy-duty jobs. Do not use power tools for heavy-duty jobs
for which it was not designed.
8. Dress properly. Do not wear loose clothing, gloves, ties or
jewelry. They can be caught in moving parts. Non-skid
footwear is recommended. Use protective hair covering to
contain long hair.
9. Wear eye protection. Always wear appropriate
safety accessories authorized by the Mexican Official
Standard (Norma Oficial Mexicana NOM). Wear
goggles, face and dust masks when working with
materials that shed metallic parts, shavings or
chemical dust.
10. Do not use the power cord for purposes different than
those it was intended. Do not carry tool by the power cord
or yank to disconnect it from socket. Protect cable from
heat, oil and sharp edges.
11. Secure work piece. Use clamps or vices to hold work piece
steady. Is safer than using one hand and enables the user
to use both hands. Keep proper footing and balance at all
times. Do not overreach over or walk across the tool when
is running.
12. Do not extend your range of activities. Avoid a standing
position that makes you get tired. Keep a safe position and
stable balance.
13. Keep tools in the best conditions. To gain better performance
keep tools clean. Follow lubrication and appliance
replacement instructions. Verify periodically the tool's cables;
if damaged have them repaired in a Truper® Authorized
Service Center. Handles should always be clean, dry and
free of oil and grease.
14. Disconnect tools. Disconnect tools when idle, and before
servicing.
15. Reduce the risk of unintentional starting. Do not
carry a plugged-in tool with your finger on switch. Be
sure switch position is OFF before plugging in power
cord.
16. Outdoor extension cords. While outdoors use only
extension cords that are equivalent and duly labeled.
17. Stay alert. Watch what you are doing. Exercise common
sense. Do not operate tool when tired.
18. Double check damaged parts. Before using the tool,
carefully check guards or damaged moving parts. Ascertain
proper operation and performance. Check moving parts
alignment, binding, breakage, mounting and any other
condition that may affect its operation. In order to guarantee
proper function of the tool, all components should be
adequately assembled and in compliance with the
requirements. Any worn switch should be replaced in a
Truper® Authorized Service Center. Do not operate any
power tool if the ON/OFF switch is not working.
19. Parts and accessory replacement. When in need of replacing
parts use only original Truper® spare parts designed to be
used with this tool.
20. Warning! For your personal safety use only
accessories or additional equipment specified in these
operating instructions or recommended by the
manufacturer. Using any other accessory not specified
in this manual may present risk of personal injury.
21. Ear protection. When performing services with a
noise level higher than 85dB wear protective earplugs.
This tool is not designed for people (children included) whose
physical, sensorial or mental capacities are reduced. Neither by
inexperienced people or with no knowledge of the tool; only if
they are supervised by persons responsible of their safety or
who have received previous instructions on how to operate the
tool.
Warning! Children should be supervised to verify they
do not play with the tool. It requires tight supervision
when disabled people or children use any power tool
or are near one.
1