Publicidad
Notes
During Assembly
Use
a
soft platform below the parts to avoid scratches and damages.
Please
note you install the panels
with
the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
IS
SIDE
OUT
and peel the
film strip covering the
panels.
Product dimensions
can be
adjusted to your specific
needs:
1.The
wall-mounting profile (top-back)
can be
adjusted from 260
to
305 cm
(102.4"
to
120")
above ground.
The
adjusting
is
done when measuring and
drilling
(Step
5).
Please
note the installation recommendations' height suggested
in
Diagram
A.
Please
note
that
the product appearance may slightly change
as
a
result,
however snow load
weight
does
not
change.
2. Poles
distance from the wall
can be
adjusted from 226
to
286 cm (89"
to
112.6")
as
suggested
in
Diagram
B1.
Poles
distance from the
side edges can be
adjusted from
5
to
54 cm
(2"
to
21.6")
as
suggested
in
Diagram
B2.
The
adjusting
is
done after assembly and before anchoring (Step 24) by sliding poles and profile 7040+7041 at the roof
profiles' channels.
3. Wall
mounting
and distance from the wall
determine the roof angle and the total depth of the product
(distance
of
gutter from the
wall). Higher wall
mounting
and shorter distance between wall and poles increase the
roof
angle and
shorten the total depth
as
suggested
in
Diagram
C.
Step_
Step
7: It
is
important to
plan the installation
area,
mark
as
per the instructions and level the surface
prior to the
assembly. Make sure you
use
suitable
screws and anchors.
Step 13:
Please
apply silicone
sealants above beam
7288
+
7290,
in
order to prevent water from seeping
in.
Step
15: Make sure
that the angle between the
back wall profile and the panel
supporting
profiles
is
90
degrees.
Step 17:
Please
note you install the panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
and peel the
film strip covering the
panels.
Step 21b:
Please
apply silicone
sealants on
both
sides
of
the part combining 8071 & 8072
in
order to prevent
water
leakage,
as
shown at the drawing 19b.
Step 22a:
Please
apply silicone
sealants on
the inner part
of
7997, and connect to the profile
as
depicted
in
drawing
20a.
Step 22c:
Please
do
not tighten
screw
4043
yet,
in
order to allow the final adjustments done
in
step 24b.
Step 24a+24c:
Please
adjust the
poles (inside
out
and sideways) by sliding them to
their final position prior to
anchoring.
Make sure
that
the poles distance from the
Patio cover side
edge does not exceed 54
cm/21.3':
Step 24b:
Please
adjust the gutter
head's
angle according to your
needs and
tighten
screws
4043.
Step 26: Anchoring this product to the ground
is
essential
to
its
stability
and
rigidity.
It
is
required to complete
this stage
in
order for your warranty to
be
valid.
*Tighten
all screws
when completing
assembly.
No
e:
The
wall anchoring kit supplied with this product
is
suitable only for concrete
walls.
Other wall types
need
an
accordant wall fixation
kit.
II
260-305cm
102.4"-120"
B1
226-286cm
89"-
112.6"
13°
EH
17°
Publicidad
