Silverline 633809 Manual Del Usuario página 6

GB
Operation
Note: This lifting device must ONLY be used by competent operators. All users
must be trained in the use of lifting equipment. Inexperienced users must receive
instruction prior to using this device. A risk assessment must be carried out before
undertaking any lifting operations.
WARNING: ALWAYS wear personal protective equipment appropriate for the work
area and type of load, including but not limited to eye protection, gloves, hard hat,
protective shoes and hearing protection.
Free-chaining (neutral mode)
WARNING: NEVER attempt to switch the Direction Control to 'NEUTRAL' when
a load is attached to the lever hoist. This may result in property damage and/or
serious, even fatal injury.
Note: In free-chaining mode the chain may be freely pulled through the Drum (2) in
either direction, either by pulling on the chain, or by rotating the Chain Brake Dial
(3). This mode can be used to adjust the chain prior to attaching a load.
1. Toggle the Direction Control (4) lever into the 'NEUTRAL' position
2. Rotate the Chain Brake Dial (3) anticlockwise, to disengage the brake
Lifting
WARNING: ALWAYS evacuate bystanders from the immediate lifting area. Clearly
communicate when lifting commences and finishes. NEVER allow anybody to
stand under a suspended load.
WARNING: Raise and lower in a smooth, controlled manner. DO NOT shock load
the lever hoist by allowing the attached load to fall freely, even for very short
distances. Ensure the chain moves freely and does not twist.
WARNING: The brake may become hot during prolonged use of the lever hoist. Stop
using the tool intermittently to ensure the brake does not overheat.
1. Ensure the lever hoist is not set to free-chaining mode (see 'Free-chaining')
2. Switch the Direction Control (4) into the 'UP' position
3. With the load safely attached as described in 'Attaching the load', operate
the Lever (5) until the Load Chain (8) is taut. Confirm that it is vertical (i.e. not
pulling at an angle)
4. Start to raise the load by further operation of the Lever. Check that it is level
with no possibility of the load tilting and/or slipping from its restraints
5. If necessary, switch the Direction Control to 'DOWN' , lower the load by
operating the Lever, and readjust slings to obtain a safe, level lift
6. Continue to raise load to required height in a slow and controlled manner. DO
NOT raise the load so far that the Load Hook (5) comes into contact with the
Drum (2)
7. To lower the load, switch the Direction Control to 'DOWN', and operate the
lever. Again, lower smoothly and slowly and DO NOT lower so far as to
completely extend the full length of the Load Chain. Stop before the Chain
End Stop (9) reaches the Drum
Accessories
• Additional lifting equipment and accessories, including lifting slings, are
available from your Silverline stockist
Maintenance
Note: All lifting equipment must be regularly inspected and maintained by a
competent person, in accordance with local laws and regulations (e.g. Lifting
Equipment Regulations, etc.). Maintenance must be recorded in a dedicated
service record (see end of this manual).
WARNING: Carry out a visual inspection of all components, every time the lever
hoist is used, and listen for any unusual sounds during operation. Perform an in-
depth examination every time the device has not been used for some time. Should
any damage be detected, remove the device from service immediately, and return
it to an authorised Silverline service centre for repairs. If the device is beyond
repair, it must be rendered unusable and discarded.
WARNING: Inspect and test the brake mechanism before every use.
WARNING: This tool does not contain any user-serviceable parts. Never
disassemble the lever hoist. Always return the device to an authorised Silverline
service centre for maintenance and repairs.
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the device's service life. Clean the body of your machine
with a soft brush, or dry cloth. If available, use clean, dry, compressed air to
blow through the ventilation holes (where applicable)
6
Lubrication
• Lubricate all moving parts with a suitable lubricant spray, at regular intervals
• Keep the load chain and both hook shanks clean and lubricated
WARNING: Never allow oil or grease to come into contact with the brake
mechanism.
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
• Tools may contain traces of tool oil, other lubricants and pollutants. Therefore,
tools should not be disposed of with household waste
• Contact your local waste disposal authority for information on the correct way
to dispose of this tool
WRONG
Figure 1
RIGHT
B
A
C
D
Figure 2