Oscartielle MAJOR Serie Instrucciones De Uso página 25

1 - Description of cabinet
The cabinets MAJOR are built in units with a usable internal length of 937 mm (MODEL 100), 1250 mm (MODEL 135),
1875 mm (MODEL 200), 2500 mm (MODEL 260), 3125 mm (MODEL 320), 3750 mm (MODEL 385), with end walls 40
mm thick and are also available with internal and external corners of 90° and 45°.
The cabinets can be multiplexed to obtain compositions of the desired length and layout, they are available with ventilated
refrigeration, both with remote unit and with incorporated compressor. A wide range of accessories and optionals is
available.
The front glasses of corner versions can be opened only by open corner 45° and 90°. The front glasses are fixed by
closed corner 45° and 90°.
The MAJOR FISH cabinet is a display case suitable for the presentation and sale of every type of fresh fish.
The general features and dimensions are clearly illustrated in FIG. 1.
2 - Transport of the unit
The cabinets are provided with wooden runners (or packed in wooden crates on request) to facilitate handling by forklift.
The insertion points of the forks for handling are shown in FIG. 2. The weights of the cabinets in the different lengths are
listed in TAB. 1.
Important: handling should be done by authorized personnel only.
3 - Arrival and storage
On delivery, make sure the cabinet has not been damaged, and check the conditions of the packing. If it shows any
damage, check the contents in the presence of the forwarder. The cabinet should be protected from atmospheric agents
and stored at a temperature between -25°C and + 55°C, with relative humidity between 30% and 95%.
Disconnect the cabinet from the fastening brackets and remove the padding around it. Remove the wooden runner by
unscrewing the holders that fix it at the cabinet, as per FIG. 3. Position the cabinet exactly where you plan to install it.
Move the cabinet carefully, never pull it by the end walls!
Unpack the cabinet with care because the glass parts and all the accessories are packed inside it.
Important: if the goods are delivered damaged, notify the manufacturer at once: any delay in reporting damage will
relieve the manufacturer of all liability.
Any damage to the cabinet occurring during shipment and storage may not be attributed to the manufacturer.
4 - Installation and environmental conditions
For correct operation, make sure the cabinet is absolutely levelled and, if necessary, adjust it by screwing or unscrewing
the feet (FIG. 4).
Do not install the cabinet in rooms where there are explosive gasses.
Do not use the cabinet out of doors or expose it to rain (FIG. 5).
The performance of the cabinet refers (according to the international standard EN ISO 23953-1/2) to environmental
climatic class 3 which consists of a room temperature of 25°C with relative humidity of 60%. If the environmental
conditions are different, or the cabinets are exposed to drafts in excess of 0.2m/sec., or heat radiations, the user must
accept inferior performance. It is possible to overcome this problem by informing the manufacturer of the effective
environmental conditions prior to drawing up the final project, in order to make possible alterations to the technical
optionals of the cabinet.
For the cabinets with plug-in unit, an adequate space should be provided in the rear part (operator side) of the cabinet to
permit maintenance and cooling of the condenser (FIG. 6). In case of a rear platform, we suggest providing a removable
part near the control panel to facilitate maintenance.
5 - Assembly of cabinet
The operations of assembly of the cabinet should be carried out exclusively by authorized personnel.
Assembly instruction of the superstructure of model Major
Assemble the superstructure according to the following sequence:
1. Position the curved upright on the fixed flask (FIG. 7 – ref. 1) insert the screws in their housings (FIG. 7 – ref. 2), then
fasten the upright.
2. Put the gasket on the curved front glass, insert the curved glass panel centering it accurately on the aluminum profile
(FIG. 8 – ref. 1) and fasten them by tightening the dowels with hexagonal wrench (FIG. 8 – ref. 2).
3. Fix the handle profile on the front glass (FIG. 9 – ref. 1). Tight it and regulate it by the plastic dowels (FIG. 9 – ref. 2).
If necessary, multiplex the cabinet as per instruction at paragraph 18.
4. If required regulate the superstructure by using the relatives screws on the upright, following the sequence of the
instruction shown in FIG. 10 – ref. 1-2-3.
5. Position the glass end walls in their housing, fasten them using the glass stoppers and their screws (FIG. 11 – ref. 1-
2-3).
6. Position the top glass shelf and the anti-mist glass in fan assisted version in their housings (FIG. 12 – ref. 1-2).
7. Complete assembly of the cabinet by applying the front bottom plate and the decoration trim (FIG. 13a and FIG. 13b).
ENGLISH
23