Panacom S10WM STAGE SOUND Manual Del Usuario página 4

PANEL/REAR PLATE/MP3 FUNCTION AND OPERATION
When you need to use the built-in MP3 encoding function, please format your USB disk (U disk
for short below) as FAT32 format in computer first and then copy the file in MP3 format in U disk.
When reading USB disk, the encoding system will engage in encoding playing according to the
generation sequence of MP3 songs file. Therefore, the song which is copied to U disk first will be
played in priority or vice versa. When the user needs to play according to the specific sequence,
they can arrange the copying sequence. If the files copied to U disk can not be played, please
inspect whether the file format is in MP3 format. If not, please switch to MP3 format in computer
and then copy to U disk in order to play normally. When copying MP3 file, you shall copy to the
catalogue of U disk. It is suggested to delete all the unnecessary files and file catalogues in order
to reduce the occurrence of reading error when the encoding is played. When the user buys U
disk, please select the ones with better quality and internal encoding supporting 64MB/128M
B/256MB/512MB/1GB/2GB/4GB/8GB and other volumes. During the playing process, please
make it far away from the places with high temperature, high magnetic field and high frequency
interference. In case of crash, please close the power and restart for recovery!
Volume: it is used to adjust the sound of volume.
TREBLE (treble): it is used to adjust the gain of music treble. Bass: it is used to adjust the gain
of music bass.
EQ (equilibrium): it is used to adjust music frequency curve and gain and attenuation within
certain frequency.
MIC. VOL (microphone volume): it is used to adjust the volume of microphone
MIC. TREBLE (microphone treble): it is used to adjust the gain of microphone treble.
MIC. BASS (microphone bass): it is used to adjust the gain of microphone bass.
ECHO (microphone echo): it is used to adjust the echo depth of microphone.
DELAY (microphone delay): it is used to adjust the effect of microphone echo delay.
MIC1 MIC2 (microphone 1 and microphone 2): they are used to connect the plug interface of the
wire microphone.
GT 1, GT2 (guitar 1 and guitar 2): they are used to connect the interface of guitar audio wire.
GUITAR. VOLUME (guitar volume): it is used to adjust the volume after the guitar input function
is amplified.
DC FUSE (DC fuse): it is used for the power to supply the fuse of the whole machine with the
protective tube of F10A/250V.
POWER (power switch): the switch break-make power is applicable to the power control of
sound amplifier of the whole machine instead of that of charging power. When the adapter is
connected, the battery charging is not controlled by the switch.
DC12V IN (12V DC power input): the interface of external power adaptor; please use the original
adapter.
CHARGING (indicator lamp of battery power): after the power adaptor is connected, the indicator
lamp will be on and battery starts to be charged FULL (indicator lamp of full charge): when
adapter is used to charge the battery, it means full charge when the indicator lamp is on.
WIRELESS MIC ANT (built-in microphone antenna): when you use wireless microphone, please
make the antenna vertically upward, so as to reach a better receiving effect.
12V BATTERY IN (external 12V battery interface): please carefully check the anode and cathode
when connecting and the applied connection line can not be smaller than 0.75 square meters.
Attention shall also be paid to the firmness when connecting it.
LINE IN (external audio interface): it is used to connect the compatible audio equipment such as
DVC and computer.
Display screen of MP3 encoding player: it is used to display the playing track, playing time or the
receiving rate under receiving status.
USD interface (U disk interface): when MP3 function of U disk is needed, insert the U disk with
MP3 songs to the interface.
SD/MMC CARD (interface of SD card and MMC card): insert SD card or MCC card with copied
MP3 songs to the interface.
Pg. 4