Publicidad
Idiomas disponibles
Idiomas disponibles
6 mm Ø bit (Fig. 1).
29. Determine the length of the rods 076058 (Fig. 7) based on the staircase dimensions and cut them. It is
advisable to bend the rod into a helical shape as close as possible to the handrail 140051. Assemble
the rods 076058. To facilitate fitting the rods in correspondence to the joining balusters, remove the
parts 033159 and 033160. Finally, tighten the parts 001011 previously fitted in the parts 034040 of the
intermediate balusters (y).
30. Complete the railing assembly by fitting the parts BF2 to the lower part of the balusters 127031 or 127035
and the parts 004051 to the sides of the treads (Fig. 1).
Landing balustrade assembly
31. Mark the distance between centres of the balusters so that you can fit at least four.
32. Screw the parts 001004 into the part 033063. Fit the part 033063 on the tie-rod 046036 with the parts
011038, 009005 and 131028 (Fig. 1).
33. Drill a hole in the landing using a 5 mm Ø bit. Position the parts 033063, using the parts 002040 and
001004 on the landing. Cut 12mm off the end baluster (in correspondence to the central column). Position
the end balusters (x) and the intermediate balusters (y) 127032 or 127036 with the parts 034040 turned
outward.
34. Cut 5 cm off one end of the straight handrail 140018 or 140053 and fasten the part 033164 using the
parts 011069 and 004034. Cut the other end based on the dimensions of the balustrade, drill a hole
using a 6 mm Ø bit to fasten the part 033164 or drill a hole using a 3,5 mm Ø bit to fasten the parts
033162+033163 with the parts 012014. Fasten the handrail 140053 using the parts 002031, checking
that the balusters are vertical. Tighten the parts 001004 (Fig. 1).
35. Depending on the position and whether there are walls around the opening of the staircase, one or two extra
balusters 127032 or 127036 may need to be positioned (Fig. 8).
36. In this case, allow for a space equidistant from the other balusters or from the wall. Drill a hole in the landing
using a 5 mm Ø bit and tighten the parts 033063, 001004 and 002040 (Fig. 1) (Fig. 8).
Fitting a balustrade on the floor (Fig. 14): determine the position of the balusters 127032 or 127036 on
the floor, on average one every 28 cm and at a distance from the edge of about 8 cm.
Warning: For circular balustrades, use the circular handrail 140073 to determine the distance of the
balusters from the edge of the floor opening; this distance varies depending on the radius of the circular
handrail supplied. In case of reinforced concrete floors, drill a hole using a 10 mm Ø bit and fit the parts
046015 fastening them with chemical resin (not provided). In case of wooden floors, drill a hole using a 6,5
mm Ø bit and directly screw on the part 046015 using the two nuts 005001. Assemble the parts 033063
with the parts 009002 and 005001. Fit the balustrade balusters (H= 910 mm) 127032 or 127036 to the
parts 033063, and lock them with the parts 001004. In case of straight balustrades, fit the reinforcement
balusters 127034 or 127037 approximately every metre. Fasten the balusters to the wall using the part
033010 with the parts 031059 008004, 011053, 033056, 011057 and 005035 (drill a hole using an 8 mm Ø
bit). Determine the length of the handrails and cut off the excess. Assemble the straight handrails 140053
or circular handrails 140073 to the balusters with the parts 002031 joining them with the parts 031076
and 046011 for straight balustrades and the parts 031073, 031077 and 002026 for circular balustrades.
Assemble any joining parts 033164, 033163, 033162 and end parts 033164 (Fig. 14).
37. Determine the length of the rods 076058 based on the dimension of the balustrade and cut them. In case
of circular balustrades, it is advisable to bend the rod into a circular shape as close as possible to the
circular handrail 140073. To facilitate fitting the rods in correspondence to the joining balusters, remove the
parts 033159 and 033160. Finally, tighten the parts 001011 previously fitted in the parts 034040 of the
intermediate balusters (y).
Final Assembly
38. To further stiffen the staircase at the intermediate points, fasten the parts 033010 to the wall and join
them to the balusters using the parts 033056. Drill a hole using an 8 mm Ø bit and use the parts 008004,
011053, 011057, 005035 (Fig. 12) (Fig. 13)
9 - Genius 050 - 060_2:Easy
Publicidad
