Special Adjustments - tormatic GTA 802 T Instrucciones De Montaje

230V
˜
K L
M N
22 22
K
L
M N
23 23
Retain these installation, operating and maintenance instructions for the full duration of the operator's service life!
24V
˜
J I H G F E
T
J I H G F E

Special adjustments

Special adjustments
Menu stage 9: Special functions
Menu stage 9: Special functions
Push butten Push butten . .
Number 9 appears in the display. Number 9 appears in the display.
Menu Menu Operating Mode Operating Mode
21 21
value value
0 0 Normal operation Normal operation (factory setting upon delivery)
1 1 Normal operation with ventilation position Normal operation with ventilation position
2 2 Operation on a double-leaf door Operation on a double-leaf door
(Reversal of rotational direction) (Reversal of rotational direction)
3 / 4 3 / 4 Side sectional door Side sectional door
Important! Remove jumper at STOP A input! Important! Remove jumper at STOP A input!
Use STOP A input for partial opening impulse generator. Use STOP A input for partial opening impulse generator.
In menu stage 2 the hand transmitter can be In menu stage 2 the hand transmitter can be
programmed for partial opening in place of the 4-minute programmed for partial opening in place of the 4-minute
light (see light (see ) )
16 16
5 5 Operation with single-lane control Operation with single-lane control
(only together with traffic light control) (only together with traffic light control)
An external photocell safety device is required. An external photocell safety device is required.
6 6 Automatic Closing Automatic Closing
An external photocell safety device is required. An external photocell safety device is required.
Set open phase in menu stage A. Set open phase in menu stage A.
7 7 Termination of the open phase via photocell Termination of the open phase via photocell
8 8 Termination of the open phase via impulse generator Termination of the open phase via impulse generator
For a description of the function please refer to the Operating For a description of the function please refer to the Operating
Instructions. Instructions.
Note Note: with all the special functions (menu value > 5), the "4-minute light" : with all the special functions (menu value > 5), the "4-minute light"
function is deleted the next time the power supply is interrupted. function is deleted the next time the power supply is interrupted.
Menu stage "A": Time the door stays Open Menu stage "A": Time the door stays Open
Push button Push button . .
The letter "A" is displayed. These phases can only be set using the menu The letter "A" is displayed. These phases can only be set using the menu
values 6 / 7 / 8 under menu stage "9". values 6 / 7 / 8 under menu stage "9".
Menu Menu Time door stays open (without warning time 10 secs.) Time door stays open (without warning time 10 secs.)
value value
0 0 0 s 0 s
1 1 10 s 10 s
2 2 30 s 30 s
3 3 60 s 60 s
4 4 90 s 90 s
5 5 120 s 120 s
6 6 150 s 150 s
7 7 180 s 180 s
9 9 240 s 240 s
Terminals Type 803 Terminals Type 803
22 22
All terminals as described under point 13, but with the All terminals as described under point 13, but with the
following special functions: following special functions:
G G "STOP A" Input - When adjusting "side sectional door" "STOP A" Input - When adjusting "side sectional door"
(menu stage 9 - 3 / 4) terminal for external pulser "partial (menu stage 9 - 3 / 4) terminal for external pulser "partial
opening" external impulse generator opening" external impulse generator
N N CLOSE status signal output CLOSE status signal output
Connection to traffic light control system, potential-free relay Connection to traffic light control system, potential-free relay
contact contact
120 V AC /0,5 A or 24 V DC /1A 120 V AC /0,5 A or 24 V DC /1A
M M OPEN status signal output OPEN status signal output
Connection to light control system, potential-free relay Connection to light control system, potential-free relay
contact contact
120 V AC /0,5 A or 24 V DC /1A 120 V AC /0,5 A or 24 V DC /1A
L L Output for connection of time switch for light Output for connection of time switch for light
Potential-free relay contact, 250 V AC / 5A Potential-free relay contact, 250 V AC / 5A
23 23
Terminal traffic light control
T traffic light control
GB
(factory setting upon delivery)
wall mounting / fitting to lintel wall mounting / fitting to lintel