Bosch AdvancedGrind 18 Manual Original página 20

20 | English
Intended use
The power tool is intended for cutting, grinding, roughing
and brushing metal materials without the use of water.
A special protective guard for cutting must be used when
cutting bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Spindle lock button
(3) Direction of rotation arrow on housing
(4) On/off switch
(5) Battery charge indicator
A)
(6) Battery
(7) Speed preselection thumbwheel
A)
(8) Battery release button
(9) Auxiliary handle (insulated gripping surface)
(10) Protective guard for grinding
(11) Mounting flange with O‑ring
(12) Grinding disc
(13) Protective guard for cutting
A)
(14) Cutting disc
A)
(15) Carbide grinding head
(16) Quick-clamping nut with bar
(17) Grinding spindle
A)
(18) Hand guard
A)
(19) Rubber sanding pad
A)
(20) Abrasive disc
A)
(21) Round nut
A)
(22) Cup brush
(23) Handle (insulated gripping surface)
(24) Extraction guard for cutting with a cutting guide
A)
(25) Diamond cutting disc
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Angle grinder
Article number
Rated voltage
A)
Rated speed min
Speed adjustment range min
Max. grinding disc diameter mm
1 609 92A 5L4 | (20.12.2019)
A)
Noise/Vibration Information
Noise emission values determined according to
EN 60745-2-3.
Typically the A-weighted noise level of the power tool are: 86
dB(A); sound power level 97 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 60745-2-3:
Surface grinding (roughing):
a
Disc sanding:
a
A)
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
AdvancedGrind 18
maintained, the vibration level may differ. This can signific-
3 603 CD9 0..
antly increase the exposure to vibration over the total work-
ing period.
V= 18
To estimate the exposure to vibration accurately, the times
-1
11,500
when the tool is switched off or when it is running but not ac-
-1
2800–11,500
tually being used should also be taken into account. This can
125
Angle grinder
Grinding spindle thread
Max. grinding spindle thread mm
length
Constant Electronic
Speed preselection
Soft start
Restart protection
Overload protection
Weight according to EPTA-Procedure 01:2014
– with additional low-vibra-
tion auxiliary handle
– with standard auxiliary
handle
Recommended ambient tem-
perature during charging
Permitted ambient temperat-
B)
ure during operation and
during storage
Recommended batteries
C)
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
C) The following chargers are not compatible with the PBA re-
chargeable battery: AL 1814 CV, AL 1820 CV, AL 1860 CV
(triax vector sum) and uncertainty K
h
2 2
= 10.0 m/s , K = 1.5 m/s ,
h
2 2
= 4.0 m/s , K = 1.5 m/s .
h
AdvancedGrind 18
M 14
21.7
●
●
●
●
●
A)
kg 2.7 (2.5 Ah)–
3.2 (6.0 Ah)
kg 2.4 (2.5 Ah)–
3.0 (6.0 Ah)
°C 0 to +35
°C -20 to +50
PBA 18V...W-.
AL 18...
Bosch Power Tools