Chicago Pneumatic CP7640 Serie Manual Del Operador página 4

EN
English
INSTRUCTION MANUAL
This product is designed for installing and removing threaded
fasteners in wood, metal and plastic. No other use permitted.
For professional use only.
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and fitting sizes
shown in the diagram below.
1/2" (12mm)
1/2" (12mm)
Lubrication
1. Use an air line lubricator with SAE #10 oil, adjusted to
two (2) drops per minute. If an air line lubricator cannot be
used, add air motor oil to the inlet once a day.
2. Check clutch oil once each month. Use 6 oz. (177ml) of
SAE #30 oil or equivalent.
Operation
1. The intended use of this impact wrench is with impact rated
sockets operating upon threaded fasteners. To operate,
pull trigger on handle. To operate in forward rotation, turn
reverse valve toward forward arrow position. To operate in
reverse, turn valve toward reverse arrow position.
2. This impact wrench is equipped with a regulator to enable
adjustment of output power.
Maintenance
1. After first year, disassemble and inspect air motor and
impacting clutch every three (3) months if the tool is used
every day. Replace damaged or worn parts.
2. High wear parts are underlined in the parts list.
Copyright 2009, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model
denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not
covered by Warranty or Product Liability.
1/2" (12mm)
CA048362 (1/2")
1/2" (12mm)
90
0 130
1/2" (12mm)
1/2" (12mm)
CA048360 (1/2")
CA048361 (1/2")
EC DECLARATION OF CONFORMITY
We, Chicago Pneumatic Tool Co. LLC, 13325 Carowinds
Blvd., Charlotte, NC 28273 USA, declare under our sole
responsibility that the product to which this declaration relates,
is in conformity with the requirements of the Council Directive
of June 1998 on the approximation of the laws of the Member
States relating to machinery (98/37/CE).
Machine Name CP7640 Series Impact Wrench
Machine Type Assembly Power Tool for Threaded Fasteners
- No other use is permitted.
Serial No. Tools with No. 09242F or higher
Technical Data
1" (25mm) Sq. Dr. Std.
Air pressure 90 psi (6.3 bar)
Air consumption 283 l/min (10 cfm)
Max. torque: 1898 Nm (1400 ft. lbs.)
Torque range: 203-1220 Nm (150-900 ft. lbs.)
Harmonized Standards Applied EN792-6
National Standards Applied ISO 8662-7, ISO 15744-2002
Name and Position of Issuer Bruno Blanchet, General
Manager
Signature Of Issuer_______________
Date of Issue September 1, 2009
Noise & Vibration Declaration*
Sound pressure level 110 dB(A) impacting, uncertainty 3
dB(A), in accordance with ISO
15744-2002. For sound power, add 11 dB(A).
Vibration value 7.6 m/s , re. ISO 8662-7.
2
For making estimates of daily vibration exposures, useful
information may be found in CEN/TR 15350: 2006,
"Mechanical vibration - Guideline for the assessment of
exposure to hand-transmitted vibration using available
information including that provided by manufacturers of
machinery"
*These declared values were obtained by laboratory type
testing in compliance with the stated standards and are not
adequate for use in risk assessments. Values measured
in individual work places may be higher than the declared
values. The actual exposure values and risk of harm
experienced by an individual user are unique and depend
upon the way the user works, the workpiece and the
workstation design, as well as upon the exposure time and
the physical condition of the user. We, Chicago Pneumatic,
cannot be held liable for the consequences of using the
declared values, instead of values reflecting the actual
exposure, in an individual risk assessment in a work place
situation over which we have no control.
CP7640 Series
Impact Wrench