Supplemental Installation Instructions - Liberty Pumps Pro680 Serie Manual De Instalación

LED indicators
Resettable breakers
Receptacles
20 amp (115v)
pump 1 and 2
15 amp (230v)
Figure 9. Indoor Version PDC Controller
RED alarm beacon
User interface buttons
LED indicators
Resettable breakers
20 amp (115v)
15 amp (230v)
Figure 10. Outdoor Version PDCW Controller
1100-Series System Controller
The 1100-Series system requires its own separate controller. Refer
to the Installation and Operation manual that came with the unit
for proper operation.

Supplemental Installation Instructions

PRO680XL-Series 10' Stack Test Basins
XL-Series sewage ejector basins are designed to withstand the 10'
stack test required by some municipalities. Proper installation of
the specified cover flange is essential to ensure that the test is
met. Strict adherence to these instructions is required. Under no
circumstances should the cover be installed in a manner
inconsistent with these instructions.
Types of Systems
XL-Series basins are available as fully assembled systems
complete with pump and discharge piping, as basin and cover
assembly kits with no pump or plumbing, and as basins only.
Follow the instructions below, as applicable, to correspond to the
specific type of system.
– 8 –
User interface buttons
9 Volt battery
backup
Power cord
PDC-115: 115V 20A
PDC-230: 230V 15A
Switch disconnect
Alarm silence
switch
Lockable latch
Alarm horn
9 Volt
battery backup
Liquid-tight Connectors
Copyright © Liberty Pumps, Inc. 2018 All rights reserved.
Basin Installation
For all systems, refer to the primary instructions supplied with this
ejector system or basin for excavating the pit, plumbing
connections, and backfilling.
Installing the Pump in the XL-Series Basin or XL Basin
and Cover Assembly Kit
1. Liberty Pumps XL-Series basins, purchased separately, will
require the appropriate 16-bolt Pro-Series cover assembly to
make an effectively sealed ejector system. Contact Liberty
Pumps customer service for the proper cover for the
application.
2. Size the length of the discharge piping to reach from the
discharge of the pump to be within the discharge pipe socket
with integral lip seal on the underside of the Pro-Series cover.
Liberty Pumps sewage pumps utilize a 17.50" long toe nipple
for 680XL-Series Basins. Install the pipe into the threaded
discharge of the pump.
3. Lower the pump into the basin, fitting the pump legs into the
torque stops.
4. Insert power cord for the pump—and the piggyback switch
cord, if so equipped—through the underside of the
inspection cover hole and position cover over pipe nipple
while aligning the bolt holes. Sealant (such as silicone) can be
applied on both sides of the rubber gasket surface to ensure
proper sealing. Use sixteen 1/4-20 UNC bolts and washers to
secure cover to the basin. Tighten bolts to 40 inch-pounds.
Do not overtighten bolts. The soft, integral gasket will
conform to the top of the tank. The bolts may be re-torqued
up to 60 inch-pounds to seal any leaks that may occur during
a 10' stack test.
5. Liberty Pumps recommends the use of manual type pumps
and the appropriate Liberty Pumps QuickTree Switch Kit for
mounting of pump control and alarm floats. Contact
customer service for ordering information. Install the
QuickTree Kit per instructions included. Liberty Pumps
automatic type pumps with piggyback float switches may also
be used. Lay the power cable and switch cable in the grooves
in the inspection cover recess as shown in the primary
instructions included with this system. Attach the inspection
cover to the main cover using supplied bolts and washers.
Sealant (such as silicone) can be applied on both sides of the
rubber gasket surface to ensure proper sealing. Tighten the
bolts furthest away from the power cord grooves first,
torquing to 40 inch-pounds. Do not overtighten bolts. The
soft, integral gasket will conform to the top of the cover and
power cords. The bolts may be re-torqued up to 60
inch-pounds to seal any leaks that may occur during a 10'
stack test.
Pro680XL Series Basins IAPMO listed, # 4361
8337000G