Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

DESCRIPTION
Model 66037 service jack is a self-contained device designed for
lifting, but not sustaining a partial vehicular load. It consists of a
frame with wheels and swivel casters supporting a mechanism that
actuates a pivoting lift arm equipped with a saddle. It is designed for
use by professional auto mechanics.
BEFORE USE
IMPORTANT! BEFORE USING THIS JACK:
The breather located below hole in cross plate must be opened. Insert
slotted screw driver through hole and turn breather screw counter
clockwise until it stops turning. Do not force screw past stopping
point.
Air may become trapped in the hydraulic system during transit.
To purge air:
1. Open release valve by turning handle counterclockwise.
2. Pump handle rapidly 4 full strokes. This will expel air
that mayhave entered hydraulic fluid passages during transit.
3. Close
release
valve
and pump handle.
4. If lift arm raises to full height, jack is ready for use. If not,
repeat this procedure or follow trouble shooting instructions
provided.
FEATURES/SPECIFICATIONS
• Heavy gauge flanged
steel frame
• Heavy duty black steel
swivel casters and 2-1/4"
wide-track front wheels
• Round cast steel saddle
with 1" thick rubber pad
• Dual piston power unit
for rapid lifting
• Dual return spring
• Safety overload system
prevents use beyond
rated capacity
66037
by
rotating
handle
clockwise
Capacity: ............. 3.5 Tons
Low Height: ..................4"
Raised Height: .......19.25"
Length: .......................29"
Chassis Width: .....14-1/2"
Handle Length: .....50-1/2"
(2 piece)
Saddle Diameter
(with pad): .................5.3"
Shipping Weight: .. 115 lbs
THIS IS A LIFTING DEVICE ONLY. DO NOT MOVE OR DOLLY THE VEHICLE
WHILE ON THE JACK. IMMEDIATELY AFTER LIFTING, SUPPORT THE VEHICLE
WITH APPROPRIATE MEANS.
DO NOT OVERLOAD. OVERLOADING CAN CAUSE DAMAGE TO OR FAILURE
OF THE JACK.
LIFT ONLY ON AREAS OF THE VEHICLE AS SPECIFIED BY THE VEHICLE
MANUFACTURER.
CENTER LOAD ON SADDLE PRIOR TO LIFTING. OFF-CENTER LOADS MAY
CAUSE DAMAGE TO JACK, LOSS OF LOAD, PROPERTY DAMAGE, PERSONAL
OR FATAL INJURY.
THIS JACK IS DESIGNED FOR USE ONLY ON HARD LEVEL SURFACES CAPABLE
OF SUSTAINING THE LOAD. USE ON OTHER THAN HARD LEVEL SURFACES
CAN RESULT IN JACK INSTABILITY AND POSSIBLE LOSS OF LOAD.
NO ALTERATIONS TO THE JACK SHALL BE MADE.
READ, STUDY AND UNDERSTAND THE OPERATING MANUAL PACKED WITH
THIS JACK BEFORE OPERATING.
FAILURE TO HEED THESE WARNINGS MAY RESULT IN LOSS OF LOAD,
DAMAGE TO JACK, AND/OR FAILURE RESULTING IN PROPERTY DAMAGE,
PERSONAL OR FATAL INJURY.
1
Rev. 09/14/05

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Sunex Tools 66037

  • Página 1 DESCRIPTION Model 66037 service jack is a self-contained device designed for lifting, but not sustaining a partial vehicular load. It consists of a frame with wheels and swivel casters supporting a mechanism that actuates a pivoting lift arm equipped with a saddle. It is designed for use by professional auto mechanics.
  • Página 2 Do not overfill. Replace breather. If low, add hydraulic fluid as needed. Maintenance and Inspection: The owner and/or user must maintain and inspect the jack in accordance with the manufacture's instruction 66037 Rev. 09/14/05...
  • Página 3 Lift Arm Assembly Pull Rod RS3530 Release Assembly Hex Nut M12 RS35BA Breather Retaining Ring RS3524-1 Cap for pump plunger Long Linkage RS3524-2 Pin for pump plunger cap 2 Retaining Ring 25 RS3543SUN Saddle Cover Shaft Arm 66037 Rev. 09/14/05...
  • Página 4 If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Repair kits and replacement parts are available for many of Sunex Tools products regardless of whether or not the product is still covered by a warranty plan.
  • Página 5 • Soporte redondo de acero fundid Ancho del chasis: ......14-1/2" con base acojinada de caucho de 1" de espesor. 66037 Longitude • Unidad de potencia con dos émbolos del mango:........50-1/2" para elevar con rapidez Diámetro del soporte •...
  • Página 6: Instrucciones Para El Funcionamiento

    NO SE DEBE USAR líquido para frenos, alcohol, glicerina, aceite para motor con detergentes ni aceite de motor usado, ya que un líquido incorrecto le puede ocasionar daños internos serios al gato. 66037 Rev. 09/14/05...
  • Página 7: Garantía Limitada

    Si tiene alguna duda relacionada con elservicio de garantEia, por favor escríbale a Sunex Tools. Esta garantía le concede derechos jurídicos específicos y quizá otros derechos que varían de un estado a otro, Sunex Tools tiene a su disposición los juegos de reparación y refacciones de repuesto para muchos de sus productos, sin importar si el producto continúe o no bajo...
  • Página 8 Information de mise en garde • Ventilation des piéces DESCRIPTION Le vérin de service modèle 66037 est un dispositif autonome conçu uniquement pour soulever, et non pour soutenir, le poids partiel d'un véhicule. Il est constitué d'un cadre avec roues et roulettes pivotantes qui supporte un mécanisme actionnant un bras de levage pivotant équipé...
  • Página 9: Lubrification

    à moteur avec détergent ou toute huile souillée; l’utilisation male et n’est pas considérée comme un vice de fabrication pou- d’un fluide inadéquat peut sérieusement endommager le système vant se réclamer de la garantie. interne du cric. 66037 Rev. 09/14/05...
  • Página 10: Garantie Limitée

    à ce produit spécifique. Ce produit a une garantie de UN AN. Pendant la période de garantie, Sunex Tools réparera ou remplacera, à sa seule discrétion, toute pièce ou tout appareil dont il a été...

Tabla de contenido