Skil F0159783 Serie Manual Original página 10

• Use only grinding/cutting discs with a maximum
thickness of 8 mm and a spindle hole diameter of 22 mm
• Never use reducors or adaptors to fit large-hole grinding/
cutting discs
• Never use accessories with a "blind" threaded hole
smaller than M14 x 21 mm
• Handle and store grinding/cutting discs carefully to avoid
chipping and cracking
OUTDOOR USE
• Connect the tool via a fault current (FI) circuit breaker
with a triggering current of 30 mA maximum
BEFORE USE
• Before using the tool for the first time, it is recommended
to receive practical information
• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
• Always mount auxiliary handle F 2 and protective guard
G 2; never use the tool without them
• Use suitable detectors to find hidden utility lines or call
the local utility company for assistance (contact with
electric lines can lead to fire or electrical shock; damaging a
gas line can result in an explosion; penetrating a water pipe
will cause property damage or an electrical shock)
• Do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when connectable
• Follow the dust-related national requirements for the
materials you want to work with
• Be careful when cutting grooves, especially in supporting
walls (slots in supporting walls are subject to country-
specific regulations; these regulations are to be observed
under all circumstances)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Do not clamp the tool in a vice
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
DURING USE
• If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
• Never use the tool when cord is damaged; have it
replaced by a qualified person
• In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
• In case of current interruption or when the plug is
accidentally pulled out, release switch J 2 in order
to prevent uncontrolled restarting
AFTER USE
• After switching off the tool, never stop the rotation of the
accessory by a lateral force applied against it
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Wear protective glasses and hearing protection
5 Double insulation (no earth wire required)
6 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
• If for any reason the old plug is cut off the cord of this tool,
it must be disposed of safely and not left unattended
USE
• Mounting of accessories 2
! disconnect the plug
- clean spindle A and all parts to be mounted
- tighten clamping flange B with spanner C while
pushing spindle-lock button D
! push spindle-lock button D only when spindle A
is at a standstill
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during use;
do not touch them until they have cooled down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it (if provided)
• Mounting of auxiliary handle F 7
! disconnect the plug
- screw auxiliary handle F on the right, the top, or the left
of the tool (depending on the work to be carried out)
• Removing/mounting/adjusting of protective guard G 8
! disconnect the plug
- open protective guard G by loosening screw H (do not
remove it)
- place protective guard G on the spindle collar of the
tool head and turn it to the required position
(depending on the work to be carried out)
! ensure that the closed side of the protective
guard always points to the operator
- fasten protective guard G by tightening screw H
• Before using the tool
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 60 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
• Electronic soft-start
Ensures reaching the maximum speed smoothly without
a sudden impact when tool is switched on
• On/off safety switch J 9
- switch on tool 9a
! before the accessory reaches the workpiece, the
tool should run at full speed
- switch off tool 9b
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
10