Jonsered LM 2146M Manual De Usuario página 7

Ocultar thumbs Ver también para LM 2146M:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 68
Do not operate the product unless the blade and all
covers are attached correctly. An incorrectly
attached blade can come loose and cause personal
injury.
Make sure that the blade does not hit objects such
as stones and roots. This can do damage to the
blade and bend the engine shaft. A bent axle causes
heavy vibration and a very high risk that the blade
becomes loose.
If the blade hits an object or if vibrations occur, stop
the product immediately. Disconnect the ignition
cable from the spark plug. Examine the product for
damages. Repair damages or let an authorised
service agent do the repair.
Never attach the engine brake handle permanently
to the handle when the engine is started.
Put the product on a stable, flat surface and start it.
Make sure that the blade does not hit the ground or
other objects.
Always stay behind the product when you operate it.
Let all the wheels stay on the ground and keep 2
hands on the handle when you operate the product.
Keep your hands and feet away from the rotating
blades.
Do not tilt the product when the engine is started.
Be careful when you pull the product rearward.
Never lift up the product when the engine is started.
If you must lift the product, first stop the engine and
disconnect the ignition cable from the spark plug.
Do not walk rearward when you operate the product.
Stop the engine when you move across areas
without grass, for example paths made of gravel,
stone and asphalt.
Do not run with the product when the engine is
started. Always walk when you operate the product.
Stop the engine before you change the cutting
height. Never make adjustments with the engine
started.
Never let the product stay out of view with the engine
started. Stop the engine and make sure that the
cutting equipment does not rotate.
Safety instructions for operation
Personal protective equipment
WARNING: Read the warning instructions
that follow before you use the product.
Personal protective equipment cannot fully prevent
injury but it decreases the degree of injury if an
accident does occur. Let your dealer help you select
the right equipment.
Use heavy-duty slip-resistant boots or shoes. Do not
use open shoes or go with bare feet.
Use heavy, long pants.
897 - 002 - 26.09.2018
Use protective gloves when necessary, for example
when you attach, examine or clean the cutting
equipment.
Safety devices on the product
WARNING: Read the warning instructions
that follow before you use the product.
Do not use a product with defective safety devices.
Do a check of the safety devices regularly. If the
safety devices are defective, speak to your Jonsered
service agent.
To do a check of the cutting cover
The cutting cover decreases vibrations in the product
and decreases the risk of injury from the blade.
Examine the cutting cover to make sure that there
are no damages such as cracks.
Engine brake handle
The engine brake handle stops the engine. When the
engine brake handle is released, the engine stops.
To do an inspection of the engine brake, start the engine
and then release the engine brake handle. If the engine
does not stop in 3 seconds, let an approved Jonsered
service agent adjust the engine brake.
(Fig. 18 )
Muffler
The muffler keeps the noise levels to a minimum and
sends the exhaust fumes away from the operator.
Do not use the product if the muffler is missing or
defective. A defective muffler increases the noise level
and the risk of fire.
CAUTION: The muffler becomes very hot
during and after use and when the engine
operates at idle speed. Be careful near
flammable materials and/or fumes to prevent
fire.
To do a check of the muffler
Examine the muffler regularly to make sure that it is
attached correctly and not damaged.
Fuel safety
WARNING: Read the warning instructions
that follow before you use the product.
Do not start the product if there is fuel or engine oil
on the product. Remove the unwanted fuel/oil and let
the product dry.
7

Publicidad

Tabla de contenido
loading

Tabla de contenido