Additional Safety Instructions; Machine Information; Technical Specifications - VONROC PM502AC Traducción Del Manual Original

of battery packs should only be performed by the
manufacturer or authorized service providers.

ADDITIONAL SAFETY INSTRUCTIONS

• Firmly tighten the mixing paddle, and remove
the spanner before starting the machine.
• Do not use the power tool for explosive
materials (e. g., easily inflammable solvents).
Power tools produce sparks which could ignite
developing vapours.
• In case the power tool should fall into the material
to be stirred, pull the plug immediately and have
the power tool checked by an after­sales service
agent. Material that has penetrated the power tool
can cause damage and lead to an electric shock.
• Hold the machine firmly with both hands by the
insulated gripping surfaces while working and
keep proper footing and balance at all times.
The machine is more securely guided with both
hands. Loss of control can cause personal injury.
• Hold power tool by insulated gripping surfaces,
when performing an operation where the acces­
sory may contact hidden wiring or its own cord.
The accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
• Switch off the power tool immediately when the
tool insert jams. Be prepared for high reaction
torque that can cause kickback. The tool insert
jams when:
- the power tool is subject to overload or
- it becomes wedged in the workpiece.
• Do not mix food. Power tools and their accessories
are not designed for processing food.
• Keep the cord away from the working area.
The cord may be entangled by the stirrer whisk.
• The mixing container must be suitable for mixing
and must stand securely. A container that is not
properly secured may move uncontrolled.
• Ensure that no liquid splashes against the
housing of the power tool. Liquid that has
penetrated the power tool can cause damage
and lead to electric shock.
• Follow the instructions and warnings in the Mate­
rial Safety Data Sheets (MSDS) of the material to
be mixed. Material to be mixed may be harmful.
• In the event of a power interruption, release the
locking switch by pressing the on/off switch.
This will prevent the power tool from restarting
unintentionally (risk of injury).
• Do not use the power tool in a stand.
WWW.VONROC.COM
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate label.
• Do not use the machine if the mains cable or the
mains plug is damaged.
• Only use extension cables that are suitable for
the power rating of the machine with a minimum
thickness of 1.5 mm . If you use an extension
2
cable reel, always fully unroll the cable.

2. MACHINE INFORMATION

Intended use
The machine is intended for mixing pulverised buil-
ding materials such as mortar, plaster, adhesives,
as well as solvent free paint, varnish and similar
substances. Improper use may damage the tool.

TECHNICAL SPECIFICATIONS

Model No.
Voltage
Frequency
Power input
No-load speed Gear 1
Gear 2
Tool mount
Whisk
Weight
Sound pressure level L
PA
Acoustic power level L
WA
Vibration
Vibration level
The vibration emission level stated in this instruction
manual has been measured in accordance with a
standardized test given in EN60745; it may be used to
compare one tool with another and as a preliminary
assessment of exposure to vibration when using
the tool for the applications mentioned.
• Using the tool for different applications, or with
different or poorly maintained accessories, may
significantly increase the exposure level.
• The times when the tool is switched off or when
it is running but not actually doing the job, may
significantly reduce the exposure level.
EN
PM502AC
230-240V ~
50Hz
1800W
180-400/min
300-700/min
M14
Ø 140mm
4.45 kg
87.6+3 dB(A)
98.6+3 dB(A)
5.187+1.5 m/s
2
5