Milwaukee 8960-20 Manual Del Operador página 5

Installing/Changing the Fleece Dust Bag
1. Unplug tool.
2. Unlatch and remove
head.
3. Remove old bag and
discard.
4. Fit the cardboard inlet
over the inlet tube.
5. Ensure the bag is con-
tained fully in the tank.
6. Replace the head and
latch it in place.
Installing the Hose and Accessories
Refer to "Accessories" for a list of adapters and dust
collection attachments.
1. Fit the hose into the inlet and twist to secure.
2. Choose the appropriate accessory and insert it
onto the hose. Twist to secure.
Cleaning/Changing the Main Filter
The dust extractor has an
automatic filter cleaning
system. During extremely
heavy or long uses, manu-
al cleaning may be neces-
sary. If manual cleaning
does not restore full suc-
tion, replace the filter. See
"Specifications" for replace-
ment part number.
1. Turn on dust extractor.
2. To manually clean the filter, place palm of your
hand over the nozzle for 10 seconds.
3. Turn off the dust extractor.
4. Unplug tool.
5. Unlatch and open the filter compartment.
6. Remove the filter and shake or tap the edge over
trash can.
7. Replace the clean filter. If filter does not clean with
tapping, replace with a new filter.
8. Close and latch filter compartment.
Cleaning the Motor Intake Filter
1. Unplug tool.
2. Press in the lock tabs
and pull the cover away
from the head.
3. Pull out the sponge filter.
4. Clean the filter and re-
place.
5. Insert the cover into the
head until the lock tabs snap in place.
After particularly dusty applications, the motor intake
filter may become clogged and cause the tool to
overload. If overload occurs, unplug the tool for 5
minutes and clean the filters.
Periodically inspect the HEPA filter and replace if
necessary. See "Specifications" for replacement part
number.
1. Unplug tool.
2. Unlatch and remove
head.
3. Place the head upside
down on a level surface.
4. Remove the 4 screws
holding the orange cover
in place.
5. Carefully remove the
HEPA filter. Note, there is a ring gasket below the
filter - do not discard the ring gasket.
6. Inspect and replace the filter and ring.
7. Replace the cover and tighten the 4 screws securely.
WARNING
moving accessories. Only use accessories spe-
cifically recommended for this tool. Others may
be hazardous.
To reduce the risk of injury, wear safety goggles
or glasses with side shields.
To increase or decrease the air flow
speed, use the speed control dial. Turn
Filter
the dial clockwise to decrease the air
flow speed, and counter clockwise to
increase the airflow speed.
Filters can become clogged during heavy use.
To maintain the efficiency of the dust extractor,
empty/change the filter bag and clean all of the
5
filters periodically. Milwaukee suggests cleaning
the filters after 200 holes (at 5/8" diameter, 4"
deep) or an equivalent amount of produced dust.
Starting and Stopping Dust Extractor
To turn on the dust extractor, set the
power switch to the ON position ( I ).
To turn off the dust extractor, set the
power switch to the OFF position (O).
5
To automatically start the dust extrac-
tor using a power tool's switch, set the
power switch to the TOOL
To use the tool without the automatic filter cleaning
function, set the power switch to the filter cleaning
OFF
recommended to turn off the automatic filter cleaning
when using the dust extractor for wet pickup.
Make sure that the tank is dry before using the dust
extractor to pick up dry materials. If the extractor tank
is wet, run the dust extractor for about 5 minutes (with-
out picking up anything) to dry the inside of the tank.
5
Changing the HEPA Filter
OPERATION
To reduce the risk of in-
jury, always unplug tool
before changing or re-
Selecting Air Speed
symbol below the TOOL or ON positions. It is
Picking Up Dry Materials
position.