DeWalt DCF887 Manual De Instrucciones página 10

Remachadora inalámbrica sin escobillas de 20 v máx* 6,35 mm (1/4")
Ocultar thumbs Ver también para DCF887:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
Features
Lanyard-Ready Attachment Kit (Fig. D–F)
(included on some models)
nOTE: Bit clip and belt hook cannot be used with the
lanyard-ready attachment kit installed.
safety Warnings specific for Use At height

WARNING:
Only use batteries that contain the integral
battery strap. Do not use unsecured batteries
while the tool is tethered. Unsecured batteries may
detach from the tool if dropped.
If the tool is dropped for any reason, the lanyard
attachment point and battery strap components
must be inspected and properly serviced prior to
re-use. The lanyard attachment point is designed
to stretch to absorb the shock of a drop. Any
permanent stretch to the device exposing the
red marked internal coils indicates it has been
compromised and must be serviced prior to reuse.
Always keep the tool and accessories tethered
when working "at height". (Maximum lanyard
length: 6.5 ft [2 m].)
Use only with lanyards appropriate for this tool
type and rated for at least 6.0 lbs (2.72 Kg).
Crush, cut or entanglement hazard. Do
not use near moving parts, mechanisms or
running machinery.
Do not anchor the tool lanyard to anything on
your body. Anchor to a rigid structure that can
withstand the forces of a dropped tool.
Make sure the lanyard is properly secure at each
end prior to use.
Inspect tool and lanyard before each use for
damage and proper function (including fabric
and stitching). Do not use if damaged or not
functioning properly.
Do not alter the lanyard attachment point or
use in a manner other than as instructed in
this manual.
Only attach tool to a lanyard with a locking
carabiner. Do not attach by looping or knotting
the lanyard. Do not use rope or cord.
Electrical shock hazard. Be sure power is off when
working in high voltage areas. Some lanyards
are conductive.
Dropped tools will swing on the lanyard, which
could cause injury or loss of balance.
Do not carry the tool by the attachment point, the
battery strap or the lanyard.
Do not attach more than one tool to
each lanyard.
Only use appropriate D
ready attachment kit. NEVER modify tools to
create attachment points.
8
WALT brand lanyard-
e
Only transfer the tool between hands while
properly balanced in a stable orientation.
Do not attach lanyards to tool in a way that
keeps guards, switches or lock-offs from
operating properly.
Avoid getting tangled in the lanyard.
Keep lanyard away from the cutting area of
the tool.
Do not use lanyards or attachment devices to get
additional leverage from the tool.
Do not use for personal fall protection.
Falling object hazard! Only change batteries,
accessories and attachments where a dropped
object won't cause a hazard below you. Consult
your Authority Having Jurisdication (AHJ) or site
supervisor for procedures for working at height.
Do not use the charger or contractor bag
at height.
Use multi-action or screw gate type carabiners. Do
not use single action spring clip carabiners.
The lanyard-ready attachment kit is intended for use by
competent personnel who are trained and knowledgeable
regarding working with tools in and around machinery
and "at height". A lanyard-ready attachment kit may only
be added to certain models and must be installed by an
authorized service center.
The lanyard attachment point
appropriate lanyards for use at height, 6.5 ft (2 m) maximum
length, rated for at least 6.0 lbs (2.72 Kg) , with locking
carabiner ends. Refer to Figure D.
Fig. D
Installing the Battery Strap Carabiner to
the Lanyard Attachment Point

WARNING: DO NOT attach the lanyard to the battery
strap. Lanyards should only be attached to the
lanyard attachment point.
The carabiner at the end of the battery strap
opened and then attached to the lanyard attachment point.
To open the carabiner:
1. Install battery into tool.
2. Flip open the carabiner tab
3. Pull the tab upward.
4. Move the carabiner locking arm
5. Attach the carabiner locking arm to the lanyard
attachment point
 12 
(Fig. F)
is for attaching
 12 
12
 13 
, should be
 14 
,
 15 
out to open.

Publicidad

Tabla de contenido
loading

Tabla de contenido