Know Your Product; Operation - SPARKY BM 1060E Instrucciones De Uso

the machine have to be acquainted with this
Manual and must be informed about its poten-
tial hazards. Children and frail people must not
use this tool. Children should be supervised
at all times if they are in the area in which the
tool is being used. It is also imperative that
you observe the accident prevention regula-
tions in force in your area. The same applies
for general rules of occupational health and
safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
▪ Power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Protection elements (Rubber bumpers)
2. ON/OFF switch
3. Electronic regulator of rotation speed
4. Lock-on button
5. Cord with plug
6. Mixing paddle
7. Spindle
8. Machine collar
9. Speed selector switch (BM2 1060CEPlus)
10. Handles
11. Ventilation slots
12. Open-end spanner SW 22
13. Wrench flat 19 mm

Operation

This power tool is supplied from single-phase al-
ternating current mains only. It is double insulat-
ed according to EN 60745-1 and IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
This power tool is designed for:
- Operation in industry and household;
- Mixing low-viscosity emulsions and viscous
materials, for example: paints, lacquer, adhe-
sives, mortar, etc.;
6
EN
- Operation with mixing paddles and acces-
sories specified here or recommended by the
manufacturer.
PRIOR TO INITIAL OPERATION
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected and dis-
connected to the power supply socket only
when this switch is in OFF position. If the plug
is connected to a receptacle while the power
switch is in the ON position, the power tool
will start operating immediately, which could
cause a serious accident.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
▪ Check the power tool and the mixing paddle
for faults, unbalanced paddle and vibrations.
Perform a trial test.
plug the power tool prior to any adjustment,
servicing or maintenance or in case of mains
drop-out..
SWITChING ON - SWITChING Off
Brief activation
Switching on: press ON/OFF switch 2.
Switching off: release ON/OFF switch 2.
Continuous use
Switching on: press ON/OFF switch 2 and in
pressed position lock it by button 4.
Switching off: press ON/OFF switch 2 once and
release it immediately.
Non-self starting safety (NVR) (only for mod-
els BM 1060CEplus and BM2 1060CEplus)
In case of mains drop-out (or temporary drop-
out for time t > 0.5 s), when the ON/OFF switch
is in ON position, the machine should not oper-
ate after supply recovering. To start operating
the machine, first switch off and then switch on
the lever of ON/OFF switch.
ELECTRONIC RPM CONTROL
Light pressure on ON/OFF switch 2 results in
low rotation speed, further pressing the switch
results in smooth increase of the rpm to maxi-
mum upon reaching the extreme position.
BM 1060E ● BM 1060CEPlus ● BM2 1060CEPlus
WARNING: Always switch off and un-