Makita DSC250 Manual De Instrucciones página 5

Cortadora de varilla a batería
Ocultar thumbs Ver también para DSC250:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

WARNING
1.
Before use, read this Instruction Manual
thoroughly.
2.
Use only the charger and battery specified in
this Instruction Manual.
·
Any combination, except that specified in this
manual, may cause injury or damage due to
explosion.
3.
Charge properly.
·
Use this charger only with the rated AC power
supply. Do not use booster transformers or vehicle
generator, or use the charger to supply DC power.
Incorrect use may cause overheating and fire.
·
Do not charge the battery at a temperature under
10°C (50°F) or more than 40°C (104°F) as this
may cause an explosion or fire.
4.
Do not short-circuit the pins of the battery.
Avoid storing battery in a container with other
metal objects such as nails, coins, etc. This
may cause overheating, fire and explosion due
to short-circuit.
5.
Guard against an electric shock.
·
Do not touch the power plug with a wet or damp
hands as this may result in an electric shock.
6.
Consider the work area environment.
·
Do not expose the charger and battery to rain or
use them in damp or wet locations, as this may
cause overheating or electric shock.
·
Keep the work area well lighted. Working where
there is insufficient light may cause an accident.
·
Do not use or charge the battery where there are
flammable fluids or gases, as this may cause
explosion or fire.
7.
Wear Safety Glasses and Protective Clothing
·
Always wear eye protection, dust mask, non-skid
safety shoes, helmet and any other mandated
or necessary protective clothing while using this
equipment. Failure to do so may result in injury.
8.
Prevent unintentional starting.
·
Ensure the switch is in the off-position before con-
necting to power source and/or battery pack, pick-
ing up or carrying the tool. Carrying power tools
with your finger on the switch invites accidents.
9.
Secure the work.
·
Use clamps or a vice to hold the work. This frees
both hands to properly hold, control, and operate
the tool. Failure to properly secure the work may
result in injury.
10. Disconnect the tools power supply, by remov-
ing the Battery and engaging the Trigger
Switch Lock, whenever one of the following
situations occur.
·
The tool is not in use or is being serviced.
·
Any parts, such as a blade, are being replaced.
·
There is a recognised hazard.
Failure to do so may result in accidental operation
and damage or injury.
11. Only use the specified accessories or
attachments.
·
Use only the accessories or attachments
described in this Instruction Manual and the
Makita catalog. Use of any other accessories or
attachments may result in an accident or injury.
12. Do not expose the battery to fire as it may
explode or generate poisonous substances.
13. Under conditions of abuse, liquid may be
ejected from the battery; avoid contact.
·
If contact accidentally occurs, flush with clear
water.
·
If liquid contacts eyes, flush with clear water and
seek immediate medical help as it may result in
loss of eyesight.
14. If operating time has reduced very signifi-
cantly, stop operating immediately. There is a
risk of overheating which may result in burns
and even an explosion.
1.
Work area safety
·
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Keep Children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
3.
Store idle power tools correctly.
·
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of
untrained users.
·
Do not store the tool and battery in locations
where the temperature may reach or exceed 50°C
(122°F), such as a metal box or car in summer.
It may shorten the battery service life or result in
smoke and fire.
4.
Do not force power tools.
·
Use the tool at the proper speed and for which the
tool was designed. Cutting too fast may result in
damage to the tool or personal injury.
·
Do not use the tool in a way that could cause the
motor to lock. It may result in smoke or fire.
5.
Use the power tool for the right application.
·
Use the power tool, its attachments and blades
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Do not use for a big tool operation.
Using for applications that are different from those
intended may result in personal injury.
6.
Dress properly.
·
Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts.
Loose clothes, jewelry or long hair can be caught
in moving parts.
·
Wear rubber gloves and non-skid safety shoes
when operating a power tool outdoors. Slippery
gloves or shoes may result in a personal injury.
7.
Do not abuse a cord of charger.
·
Never use the cord for carrying, pulling or unplug-
ging the power tool.
·
Keep cord away from heat, oil, sharp edges or
moving parts.
5 ENGLISH
CAUTION

Publicidad

Tabla de contenido
loading

Tabla de contenido