Technical Assistance; Assembly Instructions; Auxiliary Handle Assembly; Depth Gauge Assembly - VITO PRO-POWER VIMP1200 Manual De Instrucciones

EN
Cleaning:
The machine must be carefully cleaned
after each use.
Do not use aggressive cleaning
products. These products may damage
plastics and metals, compromising the
safe operation of the machine.
Maintenance:
Only maintenance works described in
this instruction manual may be carried
out; all other works must be performed
by an official distributor.
Keep all the nuts and screws well
tightened in order to ensure a safe
operation.
If any components or safety devices are
removed for maintenance works, they
must be repositioned immediately.
Use only VITO-approved tools for this
machine or technically identical parts.
Not doing so may result in personal
injuries or damages to the machine. In
case of doubt, you should contact an
official distributor.

2.6 - TECHNICAL ASSISTANCE

This machine must be repaired only by
the brand official technical service or
by qualified technicians and only with
original replacement parts.
3. ASSEMBLY
INSTRUCTIONS
3.1 - AUXILIARY HANDLE
ASSEMBLY (FIG. B)
The auxiliary handle (13) is assembled
from factory. However, before using,
it must be adjusted according to the
desired position.
The auxiliary handle's position can
be adjusted (360°) to ensure a safe
working posture with less possibility of
tiredness to its user.
28
1. Untighten the auxiliary handle (13)
counter clockwise until there is a
clearance in the fixing clamp (5);
2. Rotate the handle according to the
desired position;
3. Tighten the auxiliary handle until it
gets well fixed, rotating clockwise;
If it is necessary to remove the auxiliary
handle, follow these steps:
4. Insert the pin into de fixing screw;
5. Insert the pin into the handle fixing
clamp perforations with the screw
placed in;
6. Insert the clamp extremities and the
fixing screw into the handle perforation
and fittings, respectively;
7. Tighten the handle fixing screw
clockwise, until it gets well fixed;
3.2 - MONTAGEM DO
LIMITADOR
DE PROFUNDIDADE (FIG. C)
To ensure that you do not drill holes
with depth greater than desired, use
the depth gauge.
1. Untighten the fixing screw (12) of the
depth gauge;
2. Insert the depth gauge into the
fixation slot (12);
3. Adjust the depth gauge according to
the desired depth and tighten the fixing
screw;
3.3 - DRILLING ACCESSORY
ASSEMBLY
AND REPLACEMENT (FIG. D)
Never assembly or replace the drilling
accessory with the hammer running.
Unplug the machine before carrying
any of these operations.
With the SDS-Max accessory holder
it is possible to replace the accessory
easily and without additional help.
1. Clean the drilling accessory (1) and
lightly grease with oil or lubricant the
fitting slot;
2. Insert the drill, point chisel or chisel
into the dust shield perforation (2).
Rotate the accessory to facilitate the
engagement;
3. Make sure the accessory is well
tightened by pulling it out and checking
if it is locked;
4. To dismount the accessory, pull the
locking sleeve (3) towards the auxiliary
handle and remove it.
4. OPERATING
INSTRUCTIONS
This demolition hammer was conceived
to perform drilling and chiselling works
on concrete, brick, stone and asphalt.
When operating this machine, the user
shall be cautious and follow some
operating procedures:
� Always operate the hammer with the
auxiliary handle assembled and hold
the equipment with both hands. Losing
the equipment's control might cause
serious injuries.
� Do not apply too much pressure
against the working object. If the
speed decreases abruptly, reduce the
pressure applied.
� When the drilling accessory blocks,
turn the machine off immediately;
� Never leave the hammer before the
chisel is completely immobilized.
� Wear ear protection when operating
demotion hammers. Exposure to noise
can cause hearing loss.
� Operate the hammer in a way the
power cable keeps behind the machine
while working.