Black and Decker Powerful Solutions SMS216 Manual Del Usuario página 12

ENGLISH
Hold the main operating handle (2) and pull the carriage
(16) forward until the centre of the saw blade is over the
front of the work piece.
Operate the on/off switch (25) and press the saw arm
release lever (26) to lower the cutting head.
When the saw reaches full speed, push the main
operating handle (2) down slowly, cutting through the
leading edge of the workpiece.
Slowly move the main operating handle (2) toward the
fence to complete the cut.
Release the on/off switch (25) and allow the blade to
stop before allowing the cutting head to rise.
Chop cut
Slide the cutting head to the rear position as far as it will
go, and lock the carriage (16) with the lock knob (14).
Operate the on/off switch (25) and press the saw arm
release lever (26) to lower the cutting head.
When the saw reaches full speed, push the main
operating handle (2) down slowly, cutting through the
workpiece.
Release the on/off switch (25) and allow the blade to
stop before allowing the cutting head to rise.
Mitre cut
Switch the laser on/off switch (1) to on.
Loosen the mitre lock knob (7) and move the table to the
required angle. There are preset stops at 0°, 15°, 22.5°,
31.6°, and 45°. Tighten the mitre lock knob (7).
For any other angle use the mitre lock knob (fig. B) to
set the mitre to the required angle.
Operate the on/off switch (25), then press the saw arm
release lever (26) and lower the cutting head.
Release the on/off switch (25) and allow the blade to
stop before allowing the cutting head to rise.
Operating the high sliding fence for all bevel and
compound mitre cuts
The moveable part of the left side of the fence can be
adjusted to provide maximum support of the work piece
near the blade, while allowing the saw to bevel to a full
47° left. The sliding distance is limited by stops in both
directions.
Adjusting the fence (fig. R)
Loosen the high sliding fence clamp (43) and slide the
fence to the left.
Make a dry run with the saw switched off and check for
clearance.
Adjust the fence to be as close to the blade as practical
to provide maximum work piece support, without
interfering with the up and down movement of the arm.
12
Tighten the high sliding fence clamp (43) to secure the
fence in place.
Warning! The guide groove can become clogged with
sawdust. Use a stick or low pressure air to clear the guide
groove.
Bevel cut
Make sure that the high sliding fence is adjusted to the
correct orientation before adjusting the bevel angle.
Loosen the bevel lock handle (22) (fig. E) and move the
cutting head to the required angle. Tighten the bevel
lock handle (22).
Operate the on/off switch (25), then press the saw arm
release lever (26) and lower the cutting head.
Make sure that the arm is securely locked when bevelling.
Release the on/off switch (25) and allow the blade to
stop before allowing the cutting head to rise.
Compound cut
Make sure that the high sliding fence is adjusted to the
correct orientation before adjusting the bevel angle to
make a compound cut.
A compound cut is a combination of mitre cut and bevel cut.
Switch the laser on/off switch (1) to on.
Refer to the above procedures to perform this cut.
Release the on/off switch (25) and allow the blade to
stop before allowing the cutting head to rise.
Base moulding cut
Base moulding can be cut vertical against the fence or flat on
the table.
Refer to the following table:
Settings Vertical position
(back of moulding
is against the
Bevel angle
Moulding position Left side
Inside Mitre Left at
corner angle 45°
Moulding Bottom
position against
table
Finished Keep left
side side of
cut
Horizontal position
(Back of moulding
is flat on the table)
fence)
0° 45°
Right Left side Right
side side
Right at 0°
45°
Bottom Top Bottom
against against against
table fence fence
Keep Keep left Keep left
right side side of side of
of cut cut
0°
cut