Skil 7260 Manual Original página 9

! do not apply too much pressure on the tool; let the
sanding surface do the work for you
- do not tilt the tool in order to avoid unwanted sanding
marks
- keep ventilation slots C 2 uncovered
APPLICATION ADVICE
• Use the tool for sanding large surfaces, corners and
edges q
• Move the tool in straight movements in line with the grain
- for sanding bare wood surfaces
- for extra fine finishing
• Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
- for removing paint and for sanding of extremely rough
wood use coarse grit sizes (40, 60)
- for sanding of rough or plain wood use medium grit
sizes (80, 100, 120)
- for smoothing of wood and surfaces with old paint as
well as for finishing of bare wood use fine grit sizes
(180, 240, 320)
Use different grit sizes when the working surface is
•
rough:
- start sanding with coarse or medium grit
- finish with fine grit
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots C 2 )
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 5 will remind you of this when the need for
disposing occurs
NOISE / VIBRATION
• Measured in accordance with EN 62841 the sound
pressure level of this tool is 73.0 dB(A) and the sound
power level 84.0 dB(A) (uncertainty K = 3 dB), and
the vibration 4.1 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
b
Ponceuse
polyvalente
INTRODUCTION
• Cet outil sert au ponçage et au polissage à sec du bois,
des surfaces peintes, du plastique et du mastic
• Cet outil n'est pas conçu pour un usage professionnel
• Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
A Réservoir à poussière
B Interrupteur marche/arrêt
C Fentes de ventilation
D Adaptateur de l'aspirateur*
* NON FOURNI EN STANDARD
SECURITE
AVERTISSEMENTS DE SECURITE GENERAUX POUR
L'OUTIL ELECTRIQUE
AVERTISSEMENT Lisez tous les avertissements
-
de sécurité, toutes les instructions, illustrations et
caractéristiques fournies avec cet outil électrique.
Le non-respect du suivi de toutes les instructions reprises
ci-dessous peut provoquer un électrochoc, un incendie et/ou
des blessures graves.
Conservez tous les avertissements et toutes les
instructions pour pouvoir s'y reporter ultérieurement.
Le terme "outil électrique" dans les avertissements se
rapporte à des outils électriques raccordés au secteur (avec
câble de raccordement) et à des outils électriques à batterie
(sans câble de raccordement).
1) SECURITE DE LA ZONE DE TRAVAIL
a) Maintenez l'endroit de travail propre et bien éclairé.
Un lieu de travail en désordre ou mal éclairé augmente le
9
7260