Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
TO MEMORIZE CHANNELS
This TV is equipped with a channel memory feature which allows channels to skip up or down to the
next channel set into memory, skipping over unwanted channels.
Before selecting channels, they must be programmed into the TV's memory. In addition to normal
VHF and UHF channels, this TV can receive up to 113 Cable TV channels. To use this TV with an
antenna, set the TV/CABLE menu option to the TV setting. When shipped from the factory, this menu
option is in the CABLE setting.
TV/CABLE SELECTION
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "CH SET"
begins to flash, then press the ENTER button.
3
Press the SET + or – button until the indicator next to "TV/CABLE"
begins to flash.
4
Press the ENTER button to select the TV or CABLE mode. The arrow
indicates the selected mode.
5
Press the MENU button twice to return to normal TV viewing.
The chart below is typical of many cable system channel allocations.
CATV CHART
Number on this TV
Corresponding CATV channel
23
24
25
26
27
28
29
30
31
J
K
L
M
N
O
P
Q
R
41
42
43
44
45
46
47
48
49
EE
FF
GG
HH
II
JJ
KK
LL
MM
59
60
61
62
63
64
65
66
67
WW
AAA
BBB
CCC
DDD
EEE
FFF
GGG
HHH
77
78
79
80
81
82
83
84
85
RRR
SSS
TTT
UUU
VVV
WWW
XXX
YYY
ZZZ
95
96
97
98
99
100
101
102
103
A-5
A-4
A-3
A-2
A-1
100
101
102
103
113
114
115
116
117
118
119
120
121
113
114
115
116
117
118
120
121
119
NOTE:
Contact your cable company to determine the type of cable system used in your area.
AUTOMATIC CHANNEL MEMORY
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "CH SET"
begins to flash, then press the ENTER button.
3
Press the SET + or – button until the indicator next to "AUTO CH
MEMORY" begins to flash, then press the ENTER button. The TV will
begin memorizing all the channels available in your area. Channel
numbers will remain red until auto memorizing is complete.
4
Press the MENU button twice to return to normal TV viewing.
TO ADD/DELETE CHANNELS
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "CH SET"
begins to flash, then press the ENTER button.
3
Press the SET + or – button until the indicator next to "ADD/
DELETE" begins to flash, then press the ENTER button.
4
Select the desired channels to be added or deleted using the Direct
Channel Selection buttons (10 keys. 0-9), the CH + or – button or the
SET + or – button.
5
Press the ENTER button to select ADD or DELETE.
If an unmemorized channel was selected (step 4), the channel
indication will be red. Press the ENTER button if you wish to ADD the
unmemorized channel. The channel indicator will change from red to
green when a channel is added and the channel will be memorized.
If a memorized channel was selected (step 4), the channel indication
will be green.
Press the ENTER button if you wish to DELETE the channel from
memory. The channel indicator will change from green to red when a
channel is deleted.
Repeat Steps 4 and 5 for each channel to be added or deleted.
6
Press the MENU button three times after adding or deleting all of the
desired channels, to return to normal TV viewing.
ADJUSTING PICTURE
You can adjust the settings for color, sharpness, contrast, brightness and tint.
1
Press the MENU button.
2
Press the SET + or – button until the indicator next to "PICTURE" begins to
flash, then press the ENTER button.
3
Press the ENTER button repeatedly to select the item you want to adjust.
BRIGHTNESS
CONTRAST
COLOR
4
Press the SET + or – button to adjust the setting.
+
BRIGHTNESS
increase brightness
CONTRAST
increase contrast
COLOR
be brilliant color
TINT
be greenish color
makes picture
SHARPNESS
clearer
TO RETURN TO INITIAL SETTING
Press the RESET button while the picture adjusting mode appears on-screen.
3J91101A E
5
All manuals and user guides at all-guides.com
MENU
CH SET
PICTURE
LANGUAGE
V-CHIP SET
〈 + / – / ENTER / MENU 〉
TV
CABLE
AUTO CH MEMORY
ADD / DELETE
〈 + / — / ENTER / MENU 〉
14
15
16
17
18
19
20
21
22
A
B
C
D
E
F
G
H
I
32
33
34
35
36
37
38
39
40
S
T
U
V
W
AA
BB
CC
DD
50
51
52
53
54
55
56
57
58
NN
OO
PP
QQ
RR
SS
TT
UU
VV
68
69
70
71
72
73
74
75
76
III
JJJ
KKK
LLL
NNN
OOO
PPP
QQQ
MMM
86
87
88
89
90
91
92
93
94
86
87
88
89
90
91
92
93
94
104
105
106
107
108
109
110
111
112
104
105
106
107
108
109
110
111
112
122
123
124
125
01
122
123
124
125
5A
MENU
CH SET
PICTURE
LANGUAGE
V-CHIP SET
〈 + / – / ENTER / MENU 〉
TV
CABLE
AUTO CH MEMORY
ADD / DELETE
〈 + / — / ENTER / MENU 〉
MENU
CH SET
PICTURE
LANGUAGE
V-CHIP SET
〈 + / – / ENTER / MENU 〉
TV
CABLE
AUTO CH MEMORY
ADD / DELETE
〈 + / — / ENTER / MENU 〉
ADD
CH 012
〈 + / – / ENTER / MENU 〉
TINT
SHARPNESS
–
decrease brightness
decrease contrast
be pale color
be reddish color
makes picture softer
CONNECTION TO OTHER EQUIPMENT
The exact arrangement you use to interconnect various video and audio components to the TV is
dependent on the model and features of each component. Check the Owner's Manual provided with
each component for the location of video and audio inputs and outputs.
The connection diagrams below are offered as suggestions. You may need to modify them to
accommodate your particular assortment of components. The diagrams are intended to show
component video and audio interconnections only.
Press the TV/VIDEO selector button to select the AV mode to use the TV as a monitor.
Operate your VCR as usual.
TV/AV SELECTION
If you connect the TV to a VCR, camcorder or TV
game, through the audio/video in jacks, use the TV/
VIDEO button to make your selection.
Press the TV/VIDEO button repeatedly to select the
desired mode.
"VIDEO" will display on the screen for 4 seconds.
VIDEO
1. To connect the TV to a VCR
VCR
Front of TV
VIDEO AUDIO
To Audio/
VIDEO
AUDIO
Video OUT
(not supplied)
TROUBLESHOOTING GUIDE
Before requesting service, please refer to the following chart for the symptom and possible solution.
SYMPTOMS
• Make sure the power cord is plugged in.
• Try another AC outlet.
TV does not operate
• Power is off, check fuse or circuit breaker.
• Unplug unit for an hour, then plug it back in.
• Station or CATV experiencing problems, tune to another station.
Poor sound or No sound
• Check sound adjustments (VOLUME and MUTE).
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
Poor picture or No picture
• Check antenna or CATV connections, adjust antenna.
• Check for sources of possible interference.
• Check picture control adjustments.
• Station or CATV experiencing problems, tune to another station.
Poor reception on some
• Make sure channels are set into memory.
channels
• Station is weak, adjust antenna to receive desired station.
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
Poor color or no color
• Check picture control adjustments.
• Check antenna or CATV connections, adjust antenna.
• Check for sources of possible interference.
• Station or CATV experiencing problems, tune to another station.
• Make sure channels are set into memory.
Picture wobbles or drifts
• CATV company is scrambling signal.
• Adjust antenna.
• Check all CATV connections.
No CATV reception
• Set TV/CABLE menu option to the CABLE mode.
• Station or CATV system problems, try another station.
Horizontal or diagonal bars
• Check antenna connections, adjust or re-direct antenna.
on screen
• Check for sources of possible interference.
• Make sure TV/CABLE menu option is in the appropriate mode.
No reception above
channel 13
• If using antenna, check UHF antenna connections.
• Batteries are weak, dead or inserted incorrectly.
• Remote is out of range, move closer to TV (within 15 feet).
No Remote operation
• Make sure Remote is aimed at sensor.
• Confirm there are no obstructions between the Remote and the TV.
• Make sure the power cord is plugged in.
• No broadcast on station tuned.
• Sleep Timer is set.
TV shuts off
• Power interrupted.
• TV station experiencing problems or program tuned is not closed captioned.
Closed - Caption is not
Try another channel.
activated
• Check CATV connection or VHF/UHF antenna, reposition or rotate antenna.
• Press CAP/TEXT button to turn on the closed caption decoder.
Display is not shown in
• Select proper language in the menu options.
your language
SPECIFICATIONS
AC Power Input:
120V, 60Hz
AC Power Consumption:
73 Watts
Chassis Construction:
IC Solid state
Audio Power Output Rating:
1.5 Watts
Speaker:
3" Full Range, 8 ohm
Tuner Type:
181 Channel, Quartz PLL Frequency Synthesized
Remote Control:
Infrared, Direct Access, 2 x AAA batteries (supplied)
Receiving Channels:
VHF 2-13
UHF 14-69
CATV 01-97 (5A)-(A-3)
98-99 (A-2)-(A-1)
14-22 (A)-(I)
23-36 (J)-(W)
37-65 (AA)-(FFF)
66-125 (GGG)-(125)
Antenna Input Impedance:
75 Ohm (VHF/UHF/CATV) Coaxial Input
Input:
Video: 1.0 Vp-p 75 ohm
Audio: 300 mV, 47k ohm
Dimensions:
Width: 19-3/16 inches (488 mm)
Height: 16-3/8 inches (416 mm)
Depth: 18-5/16 inches (465 mm)
Weight:
38.6 Ibs (17.5 kg)
ACCESSORY
Remote Control with two size "AAA" batteries
29/09/2001, 10:39
2. To connect the TV to a TV Game
The TV can also be used as a display device for
many video games. However, due to the wide
variety of different types of signal generated by
these devices and subsequent hook-up variations
required, they have not all been included in the
suggested connection diagrams. You'll need to
consult each component's Owner's Manual for
additional information.
To Audio/Video OUT
Front of TV
VIDEO AUDIO
TV GAME
(not supplied)
3. To connect the TV to a camcorder
To playback from the camcorder, connect the
camcorder to the TV as shown.
To AV OUT
Front of TV
jack
VIDEO AUDIO
(not supplied)
POSSIBLE SOLUTIONS
Publicidad
Tabla de contenido
