RIKO NESA Manual Del Usuario página 11

OPERATION MANUAL
UNFOLDING THE STROLLER
In order to unfold the stroller, pull the stroller guiderail upward until fully
unfolded (fig. 1, 2).
ATTACHING AND DETACHING REAR WHEELS
To attach rear wheels, slide the wheel onto the half axle and push until it
clicks in place (fig. 3).
NOTE! Before starting to use the pram, make sure that all the wheels
have been assembled correctly. To disassemble the rear wheels, push the
button in rear suspension and remove the half axle (fig. 4,5).
ASSEMBLING AND DISASSEMBLING THE FRONT SWIVELLING
WHEELS
In order to assemble the front wheels, force their axles in the ends of
the front legs, until you hear a characteristic "click" (Fig. 6). In order to
disassemble the wheels press down the button at the upper part of the
swivelling mechanism (Fig. 7) and slide the wheel axle in. The stroller
has swivel wheels, which may be locked in a forward facing position. In
order for the wheels to swivel, twist the knob in the upper part of the wheel
mount in an anti-clockwise direction. To lock the wheels turn the knob in a
clockwise direction (fig. 8).
HANDLE HEIGHT ADJUSTMENT
It is possible to adjust the pram handle height. To perform the adjustment,
press down the round buttons on both sides of the handle
at the upper part, and then adjust the right height (Fig. 9).
PARKING BRAKE
The pram is equipped with a rear parking brake. To engage the brake,
press its lever down (Fig. 10). In order to disengage it, lift the lever.NOTE!
Before starting to push the pram, make sure that the brake has been
disengaged.
NOTE! Always engage the safety brake, when you leave the pram on
an inclined surface.
NOTE! The brake is not designed for slowing down. It should be engaged
after the pram has been stopped completely.
NOTE! The pram is not designed for running.
ADJUSTING SUSPENSION STIFFNESS
It is possible to adjust the stiffness of the pram's rear suspension. The
stiffness is adjusted using the lever under the rear suspension (fig. 11).
Repeat for both rear wheels. The suspension has two settings: stiff and
soft.
EXTRA SHOCK ABSORPTION OF THE BASSINET AND SEAT
UNIT (NESA, NANO PRO, ULTIMA)
The baby carriage comes with extra shock absorption system for the
bassinet and seat unit. The shock absorbers are adjustable. For a firm
ride, turn the knob in the lower section of the shock absorber clockwise.
For a soft ride, turn the knob anticlockwise (fig. 12).
EXTRA SHOCK ABSORPTION OF THE BASSINET AND SEAT
UNIT (SIDE)
The baby carriage comes with extra shock absorption system for the
bassinet and seat unit. The shock absorbers are adjustable. For a firm
ride, turn the knob in the lower section of the shock absorber clockwise.
For a soft ride, turn the knob anticlockwise (fig. 44).
ATTACHING AND REMOVING THE CARRYCOT
In order to attach the carrycot press it into the pram frame so that the
adapters on both sides of the carrycot lock onto the catches on the pram
frame (fig. 13). They will lock in place automatically.
ATTENTION! Make sure the carrycot is attached correctly prior to use. To
remove the carrycot press the buttons on the adapters at the sides of the
carrycot (fig. 14) and pull the carrycot upwards.
RECLINING CARRYCOT SUPPORT
The carrycot support is reclinable. To recline it into suitable position,
push and turn the knob located under the carrycot (fig. 15).
VENTILATED CARRYCOT
The carrycot is ventilated. To open the vent holes, slide the air grate
located under the carrycot (fig. 16).
CARRYCOT CANOPY AND HANDLE FOR CARRYING THE
CARRYCOT (NESA, SIDE, NANO PRO)
The carrycot comes with a canopy. Its frame also doubles up as a handle
for carrying the seat (this is a handle for carrying the carrycot
and not the entire pram).
ATTENTION! Before lifting the carrycot,
(perpendicular to the ground) whilst holding it by the handle. The
canopy is adjustable (fig. 17).
CARRYCOT CANOPY AND HANDLE FOR CARRYING THE
CARRYCOT (ULTIMA)
The canopy is adjustable. To position the canopy press the round
plastic buttons near its base (fig. 45)
ASSEMBLING AND DISASSEMBLING THE SEAT
The seat should be assembled and disassembled the same way as for
the carrycot (see ATTACHING AND REMOVING THE CARRYCOT fig.
18, 19). The seat may be assembled with its front and back facing the
movement direction (Fig. 20, 21).
NOTE! Before starting to use the pram make sure that the seat has been
assembled correctly
RESTRAINT SYSTEM
The seat is equipped with a 5-point restraint system (Fig. 22). It should be
used from the moment a baby starts to sit by itself. Unfasten the belts, by
releasing the forks from the central buckle, seat the baby, adjust the length
of the belts so that they fit closely to the baby's body, without oppressing
it, and then fasten the forks of all the belts to the central buckle. The seat
has an additional crotch strap which should be attached to the safety bar
using snaps (fig. 23). This is an additional element and not be a substitute
for using the 5 point safety harness.
NOTE! Always use the restraint system, if the baby can sit by itself.
SAFETY BAR
To attach the bar, insert its tongues into the slots in armrests. To remove
it, push the buttons located on the bottom of the slots (fig. 24).The bar is
adjustable. You can detach one of its ends and move it sideways to place
the baby inside the carriage (fig. 25).
NOTE: The bar is an extra element and you must still use the five-element
harness to secure the child.
ADJUSTING THE LEG REST
The pram is equipped with an adjustable leg rest. To move it to the right
position, press down the buttons on its both sides (Fig. 26).
ADJUSTING THE BACKREST
The seat unit can be adjusted to 4 different positions. To lower the
backrest, pull the lever in the rear (fig. 27). To lift the backrest, push it
upwards. It will automatically click into position.
CANOPY
To attach the canopy, insert its tongues into the slots in armrests (fig. 28).
To remove the canopy, push the buttons in the rear of slots and pull it
in the direction indicated by arrow (fig. 29). The position of the canopy
is adjustable. To adjust the position, pull the front of the canopy forward
or backward (fig. 30). The canopy has an additional section that can be
pulled forward. To unfold the additional section, open the zip in the rear
of the canopy (fig. 31).
RAIN FOIL
The pram is provided with a rain foil equipped with an air hole at the baby's
face height. To assemble it, put one end under the leg rest or
under the carrycot rear, and pull the other end onto the canopy (Fig. 32,
33). The foil is suitable both for the deep and stroller version.
MOSQUITO NET
position it upright
The carrycot comes with a mosquito net. To put it in place, attach one
end to the inside of the canopy using zips and stretch the other end over
the rear of the carrycot. Attach the sides of the mosquito net to the canopy
using the hook and loop fasteners (fig. 34).
INSTALLING THE CAR SEAT WITH ADAPTERS
Push the adapters into catches situated on the stroller's frame (fig.35)
and then push the car seat's catches into the adapters (fig. 36).The car
seat has an adjustable handle. To position it, push the buttons located at
its feet (fig.37).
REMOVING THE CAR SEAT AND ADAPTER
To remove the car seat, push both buttons located on its sides (fig. 38) and
pull the handle upwards. To remove the adapters, push both
buttons situated on their inner side and pull them upwards (fig. 39).
FOLDING THE STROLLER (NESA, NANO PRO, ULTIMA)
Before folding the stroller, remove the child seat or the carrycot. To fold the
stroller frame, push the button on the upper part of the guide on the right
side (40A), then pull up the levers on both sides of the guide (fig. 40B) and
push them down until total folding (fig. 41, 42).
FOLDING THE STROLLER (SIDE)
Before folding the stroller, remove the child seat or the carrycot. To fold
the stroller frame, pull up the levers on both sides of the guide (fig. 43)
and push them down until total folding (fig. 41, 42).