Watts Premier RO-PURE PLUS Manual De Instalación, Operación Y Mantenimiento página 5

Drill a Hole for the Faucet in a Sink
STEP 2
Note: Some sinks have predrilled 1¼" or 1½" holes that are suitable for
installation of your Drinking Water faucet. If so, please Skip to step Step 3.
NOTICE
Drilling a hole in a sink or countertop for faucet installation is
entirely out of the control of Watts. Watts accepts no responsi-
bility for damage resulting from installing faucet in any surface
including marble countertop or a porcelain sink.
For Marble countertops, porcelain sinks and other surfaces:
ALWAYS use a qualified contractor for drilling a hole in a marble
counter-top, porcelain sink and other surfaces because they
can crack and chip easily when drilling the hole.
NOTICE
Always use a diamond-tip drill bit and hole saw.
Step A – Determine desired location for the faucet on your sink
and place a piece of masking
tape over where the hole is to be
drilled. Mark the center of the hole
on the tape.
Step B – Using a variable speed drill set on
the slowest speed, drill a
hole through both porcelain and
metal casing of sink at the marked
center of the desired location. Use
lubricating oil or liquid soap to
keep the drill bit cool (If drill
bit gets hot it may cause the
porcelain to crack or chip).
Step C – Using a 1¼" diamond-tip hole
saw, proceed to drill the large
hole. Keep drill speed on the
slowest speed and use lubricating
oil or liquid soap to keep the hole saw cool during cutting.
Step D – After drilling, remove all sharp edges and make sure the sur-
roundings of the sink are cooled before mounting the faucet.
Watts Top Mount Twist Faucet Installation
STEP 3
This RO faucet is equipped with quick connect fittings for easy tube
installation. To connect tubes, simply push them firmly into their cor-
responding fitting on the RO faucet until fully seated.
NOTE:
A 1" to 1¼" mounting hole is required for the
faucet installation
NOTICE
The quick-connect ports on the faucet are color coded. Make sure the
tube being inserted matches the color of the port.
Step 3-1 – In the parts bag, locate one ¼" red tube, one ¼" blue tube
and one ⁄ " black tube.
3
8
NOTICE
Approximately 3/4" of ALL tubing must go into the fitting.
Step 3-2 - The BLUE tubing has one BENT end and one STRAIGHT
end. Connect the STRAIGHT end of the ¼" BLUE tube firmly into the
faucet fitting.
Step 3-3 – Connect the ⁄ " BLACK tube into the bottom of the faucet.
3
8
/ " pilot
1
8
Step 3-4 – The RED tubing has
one BENT end and one
STRAIGHT end. Con-
nect the STRAIGHT
end of the ¼" RED
tube firmly into the
faucet fitting.
Step 3-5 – Make sure the Locking
Tabs are "tucked".
Feed the tubes and the
lower faucet assembly
through the mounting
hole in the sink. Test fit
the faucet placement.
Step 3-6 – Make sure the lower fau-
cet assembly is seated
properly inside of the
rubber washer groove.
Step 3-7 – Using a Phillips screw-
driver, tighten the two
screws until snug. Then
tighten each screw
alternately until faucet
is secure.
NOTICE
Do not overtighten
Step 3-8 – Inspect O-rings on lower
faucet assembly. Lubri-
cate with water-soluble
lubricant if needed.
Step 3-9 – Align the release but-
ton on the back of the
upper faucet assembly
approximately 45° left
off the back of the
lower faucet assembly.
Step 3-10 – Press the upper
faucet assembly firmly
on-to the lower faucet
assembly and twist
clockwise until locked
into place. Remove battery cover on faucet handle, pull
battery tab and replace battery cover.
NOTICE
To Remove Upper Assembly: Press in the release button and twist
upper faucet assembly counter-clockwise.
L.E.D. Faucet Monitor Indicator
This faucet is equipped with a filter change indicator. The indica-
tor light will flash BLUE while the water is being dispensed. After
approximately six months or 2000 gallons of filtered water used the
light will change to RED, indicating that filters should be changed.
After filter change you must reset the monitor (Follow the Faucet
Indicator Battery Replacement procedure on page 8).
KEEP AWAY FROM CHILDREN
This product contains a button (coin) cell battery. If swallowed,
it could cause severe injury or death in just 2 hours. Seek
immediate medical help. Contact a Poison Control Center.
5