Publicidad
Idiomas disponibles
Idiomas disponibles
Also refer to the table below.
Conductor size (mm
2
)
0.75
1.00
1.50
2.50
4.00
Voltage
Amperes
115
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
230
0 - 2.0
2.1 - 3.4
3.5 - 5.0
5.1 - 7.0
7.1 - 12.0
12.1 - 20.0
Assembly and adjustment
Prior to assembly and adjustment always
unplug the tool.
Inserting and removing a bit (fig. A)
Keyed chuck (9)
• Open the chuck by turning the sleeve (10)
counterclockwise and insert the bit shank.
• Put the chuck key (11) into each hole in the side
of the chuck and turn clockwise until tight.
Keyless chuck (8)
• Open the chuck by turning the sleeve
counterclockwise and insert the bit shank.
• Tighten firmly by turning the sleeve clockwise.
• To remove the bit, proceed in reverse order.
Fitting the side handle (fig. A)
The side handle (6) can be fitted to suit both RH- and
LH-users.
Always use the Drill with the side handle
properly assembled.
15
Cable rating (Amperes)
6
10
15
20
25
Cable length (m)
7.5
15
25
30
45
Cable rating (Amperes)
6
6
6
6
6
6
6
6
15
6
6
10
15
20
10
10
15
20
20
15
15
20
25
25
20
20
25
-
6
6
6
6
6
6
6
6
6
6
6
6
10
10
10
10
10
15
15
15
15
15
20
20
20
20
20
25
• Loosen the side handle.
• For RH-users, slide the side handle clamp over the
43 mm collar behind the chuck, handle at the left.
• For LH-users, slide the side handle clamp over the
43 mm collar behind the chuck, handle at the right.
• Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. B)
• Insert the required drill bit into the chuck.
60
• Slacken the side handle (6).
• Fit the depth adjustment rod (7) through the hole
6
10
in the side handle clamp.
15
• Adjust the drilling depth as shown.
20
• Tighten the side handle.
25
-
Forward/reverse slider (fig. C)
-
-
• To select forward or reverse rotation, use the
6
6
forward/reverse-slider (4) as shown
6
6
(see arrows on tool).
15
15
Chuck removal
20
-
Keyed chuck (fig. D)
• Open the chuck jaws as far as possible.
• Insert a screwdriver into the chuck and remove
the chuck retaining screw (12) by turning
clockwise as shown.
• Insert the chuck key into one of the holes in the
side of the chuck and strike it with a hammer.
Keyless chuck (fig. E)
A pair of wedges (13) is required to remove the
keyless chuck.
• Place the wedges as shown and tap with
a hammer to remove the chuck.
Instructions for use
Prior to operation:
• Insert the appropriate bit.
• Mark the spot where the hole is to be drilled.
• Be aware of the location of pipework and wiring.
• Apply only a gentle pressure to the tool. Excessive
force does not speed up drilling but decreases
tool performance and may shorten tool life.
Always observe the safety instructions
and applicable regulations.
E N G L I S H
en - 4
Publicidad
