Atlas Copco ETP SB33-12-I06-W Manual De Instrucciones página 4

Safety Information
• Sound power level <80 dB(A) , uncertainty 3 dB(A), in
accordance with ISO15744.
• Vibration total value <2.5 m/s
cordance with ISO28927-2.
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We, Atlas Copco Industrial Technique AB, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your "Customer
Center" for handling.
4
2 2
, uncertainty - m/s , in ac-
http://
and selecting 'Tools' then 'Legis-
© Atlas Copco Industrial Technique AB - 9834 4071 00
Conformity to North American Standards
3008099
FCC and ISED Compliance Statement
This device complies with Part 15 of the FCC Rules. Any
changes or modifications not expressly approved by the man-
ufacturer could void the user´s authority to operate this de-
vice.
Operation is subject to the following two conditions:(1) this
device may not cause harmful interference, and (2) this de-
vice must accept any interference received, including inter-
ference that may cause undesired operation.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 919 272 7837
Email: rodney.hill@us.atlascopco.com
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial
environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own ex-
pense.
ISED Compliance Statement:
This device complies with: CAN ICES-3 (A)/NMB-3(A)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following
two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
ETP SB33-12-I06-W
Listed
Conforms to UL 62841-1 and
UL 62841-2-2 Std.
Certified to CSA C22.2 No.
62841-1 and CSA C22.2 No.
62841-2-2 Std.