Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Publicidad
Tabla de contenido
Manuales relacionados para Biamp Vocia VA-8600
Resumen de contenidos para Biamp Vocia VA-8600
- Página 1 VA-8600 and VA-8600c OPERATION MANUAL 585.0267.90C JANUARY 2016...
- Página 2 VA-8600 Product Description The VA-8600 is a networked multi-channel amplifier. It is CobraNet enabled and features eight channels of modular amplification and DSP with optional channel-to-channel or device-to-device failover. The VA-8600c is a networked multi-channel amplifier. It is CobraNet enabled and features eight channels of modular amplification and DSP with optional channel-to-channel or device-to-device failover.
-
Página 3: Setup And Use
VA-8600 Setup and Installation Setup and Use The Vocia software provides an intuitive interface for configuration of the VA-8600 and VA-8600c Amplifiers. The information supplied by this manual relates to physical connections and assignment. For more details on software setup, please consult the Vocia Help File. Installation The unit requires one 3.5 inch (88.9mm) high and 19 inch (483mm) wide rack space with 17.5 inch (444mm) depth. - Página 4 VA-8600 Front System Indicators The LED indicators on the front panel provide information about the function and operational status of the VA-8600 and VA-8600c chassis and any installed AM-600 or AM-600c amplifier modules. Columns one through eight correspond to the eight amplifier module slots. The remaining LEDs correspond to the VA- 8600 and VA-8600c chassis.
- Página 5 Amp Fault An amber LED illuminates when a chassis or amplifier module fault has occurred. Flashing Amber LED - Warning -the amplifier chassis or an AM-600 module is not operating within normal limits. If the condition causing the warning is not corrected, chassis failure may occur.
- Página 6 This plug is the main disconnecting device and should remain readily operable. There are no user interchangeable parts. Please contact Biamp Technical Support or your local distributor for all service requirements.
- Página 7 Logic I/O The Logic I/O connector on the NM-1 facilitates redundant device failover only. It is not a general-purpose contact closure interface. See the Amplifier-to-Amplifier Failover section below. Page Active Relays An optional Page Active Relay card can be added to the VA-8600(c) to provide a contact closure audio activity is detected on a particular output channel.
- Página 8 VA-8600 Fault Detection Amplifier-to-Amplifier Failover Vocia supports one-to-one automatic amplifier failover in case of fault. Failover is triggered by one of the following conditions: Chassis fault Channel fault Loss of power Loss of CobraNet link Loss of Logic I/O Only faults (e.g., heat sink fault and channel failure fault) trigger the failover mechanism.
- Página 9 Channel-to-Channel Failover In addition to entire amplifier failover, Vocia supports channel-to-channel failover, which is triggered by one of the following conditions: • Heat Sink fault • Short Circuit fault • Channel Failure fault The wire failover link cable is not required when wiring channel-to-channel failover. The redundant channel can be wired in parallel to the existing speaker line (shown above) or connected to a redundant speaker line.
-
Página 10: Specification Table
VA-8600 Specifications Specification Table Connection: RJ45 with shielded Ethernet Power: cable (CAT5, 5e, 6 or 7) 100V-240V AC, 50/60 Hz Dimensions: Environment: Height: 5.25 Inches (133mm) Ambient Operating Temperature: 32-113°F Width: 19 Inches (483mm) (0-42°C) Depth: 17.25 Inches (438mm) Humidity: 0 - 95% Chassis Weight: 50 lbs (22.68 kg) - Página 11 VA-8600 Specification VA-8600/8600c 115 VAC Current Draw and Heat Output To determine the AC line current draw and heat output for the configuration, start by finding the total power for the configured Vocia chassis. Then refer to the column that describes the type of audio levels the amplifier will be producing.
- Página 12 Notes Page...
-
Página 13: Fcc Notice
CAUTION – changes or modifications not approved by Biamp could void the user’s authority to operate the equipment... -
Página 14: Important Safety Instructions
To reduce the risk of fire, use only No. 26 AWG solid copper wire for telecom circuit connections. Intended for Installation and Service by Skilled Personnel Only: CAUTION – To reduce the Risk of Electric Shock, Installation and Service of Biamp Products should be conducted only by Skilled Persons who are Biamp Qualified Audio Installation Professionals. -
Página 15: Instrucciones De Seguridad Importantes
Para la instalación y mantenimiento solo por parte de personal calificado: PRECAUCIÓN – Para reducir el riesgo de descarga eléctrica, la instalación y el mantenimiento de los productos Biamp deben ser realizados por personas calificados que formen parte de los Profesionales capacitados en la instalación de audio de Biamp. -
Página 16: Consignes De Sécurité Importantes
Installation et interventions réservées au personnel compétent: MISE EN GARDE – Pour limiter les risques d’électrocution, l’installation des produits Biamp et les interventions sur ces produits doivent être réalisées uniquement par du personnel compétent faisant partie des professionnels d’installation audio qualifiés de Biamp. -
Página 17: Wichtige Sicherheitshinweise
Brandrisiko zu reduzieren. Ausschließlich für Einbau und Wartung durch geschultes Personal vorgesehen: VORSICHT – Zur Verringerung der Stromschlaggefahr sind Einbau und Wartung von Biamp-Geräten ausschließlich durch geschulte Personen, bei denen es sich um von Biamp geschulte Audio-Fachleute handelt, vorzunehmen. Führen Sie keine anderen als die in der Betriebsanleitung angegebenen Wartungsarbeiten aus, vorausgesetzt, Sie wurden hierfür geschult. - Página 18 警告 – 由市电供电的产品采用了安全接地技术，必须与正确接地的市电插座连接，才能提供接地防护。 断开设备连接 – 市电插头可用于断开 市电电源且必须保持时刻可运行状态。 小心 – 在提供了 POTS 电话接口选项时，必须由训练有素的人员将电话接口与本设备的电信回路进行连接。为减少火灾风险，只能使用 26 号 AWG 实心铜线连接电话端口。 只适用于专业技术人员来执行的安装和服务： 小心 – 为减少电击带来的风险，Biamp 产品的安装和服务应该只能由 Biamp 音频安装专业技术人员来执行。 除非您是专业技术人员，否则不能执行未包含在操作说明中的任何服务。 在打开产品之前，专业人员必须先断开交流市电电源。 小心 – “辅助电源”的安装步骤只适用于专业技术人员，而且必须遵循所有的本地法规。 • 对于美国，国家电气法规 ANSI/NFPA 70。 • 对于加拿大，加拿大电气法规第 1 部 CSA C22.1 第 2-128、12-010(3) 和 12-100 节。...
- Página 19 위험을 줄이기 위해서는 전기 통신 회로 연결은 26번 AWG 솔리드 동선만 이용하십시오. 공인 전문가의 설치 및 서비스: 주의 – 전기 충격의 위험을 줄이기 위해, Biamp 제품의 설치 및 서비스는 Biamp 공인 오디오 설치 전문가에게 의뢰해야 합니다. 전문 인력이 아닌 경우, 작업 지침에 담긴 내용 이외의 사항에 대해 서비스를 제공하면 안됩니다.
- Página 20 .لتمديدات روابط دائرة االتصاالت AWG 26 :هذا الجهاز معد للتركيب والصيانة من قبل الموظفين الماهرين فقط Biamp إال من قبل األشخاص المهرة وهم المهنيون المؤهلون تنبيه - للحد من خطر حدوث صدمة كهربائية، ينبغي أال يتم تركيب وصيانة منتجات .Biamp في...
-
Página 21: Importantes Instruções De Segurança
Destinado para Instalação e Manutenção apenas por Pessoal Qualificado: ATENÇÃO – Para reduzir o risco de choque elétrico, a instalação e a manutenção dos produtos Biamp devem ser realizadas somente por pessoas qualificadas, que são profissionais de instalação de áudio qualificados da Biamp. -
Página 22: Важные Инструкции По Технике Безопасности
одножильный медный провод типа 26 AWG. Предназначено для установки и обслуживания только опытным персоналом ПРЕДОСТЕРЕЖЕНИЕ! Для снижения риска поражения электрическим током установку и обслуживание устройств Biamp должны выполнять только лица, которые являются опытными специалистами по установке аудиосистем Biamp. Не проводите какое-либо обслуживание, помимо указанного в инструкциях по эксплуатации, если вы не обладаете соответствующим опытом и... - Página 23 RoHS COMPLIANT This Biamp product, including all attendant cables and accessories supplied by Biamp, meets all requirements of EU Directives 2011/65/EU of 8 June 2011, the EU RoHS Recast. An EU RoHS Materials Content Declaration document may be obtained at www.biamp.com (This information is presented to comply with the requirements of Chinese law SJ/T11363-2006) 有害物质表...
- Página 24 The Warranty Period for the products described in this manual shall be five (5) years. The Warranty Period begins (a) the date of the original end user’s purchase from an authorized Biamp Systems dealer or (b) six months after the product is first shipped from Biamp Systems’...