Publicidad
Idiomas disponibles
Idiomas disponibles
controlled with the trigger.
1. Service position (eBZ 2 / eBZ 3 / eBZ D):
Press the trigger (I) for 5 seconds (until the
white LED (H) on the tool starts to flash 1/sec)
and release again. The setting tool remains in
the rearmost position. The nosepiece (A) can
now be easily changed or the clamping mecha-
nism serviced. Press the trigger briefly and the
tool moves to its starting position.
2. Auto and Manual mode: In Manual mode,
hold the trigger depressed during setting of the
fastener until the fastener mandrel is sheared
off. In Auto mode you only have to press the
trigger briefly and the tool controls the setting
process automatically. To change from one
mode to the other, hold the trigger pressed for
10 seconds (until the white LED (H) on the tool
starts to flash 2/sec) and release again. Press
the trigger briefly and the tool moves back to its
starting position.
3. Deactivating the counter eBZ ZERO): After
100 fasteners, the setting tool prompts you to
change the collecting bin by alternate flashing
of the yellow and red LED (D). To activate
or deactivate this function, hold the trigger
pressed for 20 seconds. The yellow and red
LED (D) flashes. The white LED (H) in the foot
indicates whether the function is activated or
deactivated. If the white LED (H) is lit continu-
ously, the function is deactivated. If the white
LED (H) is flashing, the function is activated.
FAULTS, ERROR MESSAGES
If fasteners are used beyond the specified perfor-
mance capability of the tool, the tool stops, the red
LED (D) comes on and the tool moves back to its
starting position. Wait until the LED (D) goes out,
then you can continue to work again.
When the battery (F) is discharged, the setting
tool is protected by a protection circuit. The setting
tool completes the cycle and then stops. The LED
(D) lights up yellow. Now replace the discharged
battery with a charged battery (F). The yellow LED
(D) goes out and you can continue to work.
If an incorrect battery is installed, the LED (D)
flashes alternately red and yellow (eBZ ZERO: red
and green). Please replace the battery with a bat-
tery of the correct voltage (F). The LED (D) goes
out and you can continue to work.
Rivdom eBZ ZERO
An acoustic signal sounds at every error message.
If LED (D) flashes alternately red and yellow,
please empty the collecting bin.
To reset the counter function it is necessary to
remove the collecting bin for at least 2 seconds.
If LED (D) flashes alternately green, red and yel-
low, service is necessary.
This message is repeated every 100 setting opera-
tions or after a restart of the setting tool.
Please send the tool to an authorised service
centre.
COVER CAP
All setting tools are equipped with a cover cap,
the "cover cap", and thus conform also to the
Machinery Directive. This prevents the tool being
used without collecting bin (E). Never operate the
tool without collecting bin (E) or cover cap (J).
Never bypass the cover cap. If you have to work
in confined spaces, the cover cap (J) can be fitted
instead of the collecting bin (E). When working with
cover cap (J), hold the setting tool with the nose-
piece (A) facing downwards after each set fastener
to ensure that the sheared fastener mandrel drops
out of the tool to the front. Do not use fixed or
retainer nosepieces together with the cover cap (J).
This would result in damage to the tool!
HANGER BRACKET
If you wish to use the tool on a balancer, you can
attach the hanger bracket supplied (K) to the two
bores (C) provided. Take care not to stretch the
hanger bracket (K) too far apart so that it does not
lose its tension. Check that the hanger bracket (K)
is fitted securely before using the tool.
BELT CLIP
Attach the belt clip (O) to the foot of the tool using
the screw (M). A corresponding thread and two
slots (L) are recessed in the foot of the housing on
both sides of the tool. Check at regular intervals
that the clip (O) is still securely attached, otherwise
retighten the screw (M).
English | 17
Publicidad
