To Operate the Blender
1. Fill the beaker or a similar vessel with food.
2. Connect the blending attachment to the motor unit and turn counter-
clockwise until it clicks into place.
3. Plug in the appliance. Select the required speed setting.
4. Hold the vessel steady and place blending attachment in the food. Press
and hold down the Power button. When processing raw vegetables, fruits,
and other hard foods turn the speed control knob to increase the speed
or press and hold down the Turbo mode button.
5. Blend foods using circular up-and-down motion.
6. After use unplug the appliance. Turn the blending attachment clockwise
to disconnect from the motor unit. Clean the appliance following the
procedure outlined in "Cleaning and Maintenance" section.
To Operate the Whisk
1. Fill the beaker or a similar vessel with food.
2. Insert the whisk attachment to the gear box until it clicks into place.
3. Connect the gear box to the motor unit and turn counterclockwise until
it clicks into place.
4. Plug in the appliance. Turn speed control knob clockwise to setting 1
(minimum speed).
5. Hold the vessel steady and place whisk attachment in food. Press and
hold down the Power button. Turn the speed control knob counterclock-
wise to increase the speed if necessary (from 1 to 5). To whisk at a
maximum speed press and hold down the Turbo mode button.
6. Whisk foods using clockwise circular motion.
7. After use unplug the appliance. Disconnect the attachment and the gear
box from the motor unit by turning clockwise. Clean the appliance fol-
lowing the procedure outlined in "Cleaning and Maintenance" section.
To Operate the Chopper
1. Place the chopper bowl on a flat and stable surface.
2. Remove the protective plastic cover from the chopper blade. Fit the blade
on the central pin at the bottom of the chopper bowl. Note: the blade is
very sharp, handle with caution! Always hold the blade by the plastic collar.
3. Fill the bowl with food. Do not fill above the maximum fill mark (500 ml).
4. Fit the lid onto the bowl, aligning the crosspiece of the plastic collar with
the corresponding notches in the center of the lid. Gently press the lid
down and rotate clockwise.
5. Connect the motor unit with the chopper gear box until it clicks into place.
6. Plug in the appliance. Select the speed setting: harder foods require
higher chopping speed.
8
7. Holding the bowl with one hand press and hold down the Power button
or TURBO mode button. Use TURBO mode to chop meat and other hard
foods. Maximum continuous operation time must not exceed 1 minute.
8. After use unplug the appliance. Press release buttons on the motor unit
and disconnect the motor part. Twist the lid counterclockwise to remove.
Remove the blade, holding it by the plastic collar.
9. Clean the blade and put protective plastic cover back on.
III. CLEANING AND MAINTENANCE
Wipe the motor unit with soft damp cloth.
DO NOT immerse in water or wash the motor unit under running water.
Wash the removable parts in warm soapy water. Mix water with lemon juice to
add extra shine to metal parts of the appliance. Exercise caution when cleaning
the blades, they are extremely sharp. Rinse the blades under hot running water.
Do not use sponge with hard or abrasive surface or abrasive and solvent-based
cleaners (gasoline, acetone, etc.).
Let all parts of the appliance dry thoroughly before use.
Thoroughly clean and dry all parts of the appliance before storing. The appliance
must be stored in a dry well-ventilated location away from direct sunlight or
heating appliances.
Some foods (such as carrot and beet) may stain the plastic. Apply bleach-based
solution immediately after use to remove the stains.
IV. BEFORE CONTACTING SERVICE CENTER
Problem
Possible cause
Power cord is not connected
to an electrical outlet
Appliance does
not work
Electrical outlet is not
working properly
Strong vibration
Food pieces are too large
during operation
Solution
Connect the power cord to an electrical
outlet
Connect to properly working electrical
outlet
Cut food into smaller pieces