Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
NOTE:
If this saw is to be used for commer-
cial Icggthg, a chain brake is required and shall
not be removed or otherwise
disabled to com-
ply with Federal OSHA Regulations
for Com-
mercial Legging,
SAFETY
NOTICE:
Exposure
to vibrations
through
prolonged
use of gasoline
powered
hand tools could cause b]oed vesse] or nerve
damage
in the fingers,
hands, and joints of
people
prone
to
circulation
disorders
or
abnormal
swellings,
Prolonged
use in cold
weather
has
been
linked
to blood
vessel
damage
in
otherwise
healthy
beop]e,
If
symptoms
occur
such as numbness,
pain,
loss of strength, change in skin color or texture,
or loss of feelieg in the fingers, bend& or joints,
discontinue
the use
of this tool
and seek
medical
attention.
An anti-vibration
system
does not guarantee
the avc_dance of these
problems.
Users who operate power tools on
a continual
and regular
basis must monitor
closely
their
physical
condition
and
the
condition of this tool
SPECIAL
NOTICE:
Your saw is equipped
with a temperaturelimiting
muffler and spark
arresting
screen
which
meets
the
requirements
of California
Codes 4442 and
4443.
All U.S. forest land and the states of
California,
Idaho,
Maine,
Minnesota,
New
Jersey,
Oregon,
and Washington
require by
law that many
internal
combustion
engines
to be equipped
with a spark arresting screen.
If you operate a chain saw in a state or locale
where such regulations
exist, you are legally
responsible
for maintaining
the operating
condition
of these parts.
Failure to do so is
a violation
of the law. Refer to the SERVICE
section
for
maintenance
of
the
spark
arresting
screen.
Failureto
follow all Safety Rules and Precau-
tions can result in serious
injury. If situations
occur which are not covered
in this manual,
use care and good judgement.
If you need
assistance,
contact your authorized
service
dealer
or call 1-800-554-6723.
STANDARDS:
This saw is ]isted by Under-
writer's
Laboratories,
Inc., and the Canadian
Standards Association
in accordance
with:
ANSI
BI75.1=280g
American
National
Standard
for
Powered
Tools
~ Gasoline
Powered
Chain Saw ~ Safety Requirements
CSA Z62.1-03
Chain
Saws ~ Occupational
Health and Safety
CSA Z62.3-96
Chain Saw Kickback
Occu-
pational
Health and Safety
Protective
gloves
(not provided)
should
be
worn during assembly.
ATTACHING
THE
BAR & CHAIN
(If not
already
attached)
_]kWARNING:
If received
assembled,
repeat all steps to ensure your saw is properly
assembled
and all fasteners
are secure.
Al-
ways wear gloves when
handling the chain.
The chain is sharp and can cut you even when
it is not moving!
1. Loosen and remove the chain brake nuts
and the chain brake from the saw.
2.
Remove
the plastic
shipping
spacer
(if
present).
Location
of shipping
spacer
a_
Chain
Brak_e
Ch
Nuts
Bar Tool
3.
Turn
adjusting
screw
on bar counter-
clockwise
to move the tensioning
rack as
far as it will go toward the front of the bar.
(__
Adjusl_g
Tensioning
Rac_k
_
4.
Slide the bar behind clutch drum until bar
stops against
clutob drum sprocket.
5.
Prepare the chain by checking
the proper
direction. Without following the illustration it
is easy to I_ace the chain on the saw in the
wrong direction.
Use the illustration
of the
chain to determine the proper direction.
Tip of
Bar
DIIRECTION
OF ROTATION
Cutters
Dept_ Gauge
Drive Links
Publicidad
Tabla de contenido
