Product Specifications - Homewerks Worldwide Tosca H91K-51D-CH Manual Del Usuario

Grifo de la cocina, acabado en cromo pulido con jalador desplegable y dispensador de jabón, – acabado en acero inoxidable pulido con jalador desplegable y dispensador de jabón
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

PRODUCT SPECIFICATIONS

SPECIFICATIONS
Max. Flow Rate: 1.8 GPM (6.8 LPM) at 60 PSI
ASME A112.18.1/CSA B125
NSF 61-9
Polished chrome or stainless steel finish
ASSEMBLY INSTRUCTIONS
1.
Turn off water at the supply valve
under the sink or at the main water
supply, disconnect the supply line,
and remove old faucet.
Clean and dry surface area where
new faucet will be mounted.
Optional Flange Installation:
2.
Shut off water supplies. Remove
old faucet. Clean sink surface in
preparation for new faucet. Before
installation, ensure that the flange
(1) is placed on the bottom of the
new faucet assembly (2). Insert the
faucet assembly (2) through the hole
in the sink.
Optional Escutcheon Installation:
3.
Shut off water supplies. Remove old fau-
cet. Clean sink surface in preparation for
new faucet. Before installation, remove
the flange (1). Screw the bolts (2) into
the escutcheon (3) and ensure that the
gasket (4) is pressed onto the escutcheon
(3) before the escutcheon (3) is installed
over the three holes in the sink. Secure
the escutcheon (3) to the sink using the
mounting nuts (5) provided. Hand tighten
only. Insert the faucet assembly (6)
through the hole in the escutcheon (3).
NOTE: A silicone is required under the
gasket (4).
4.
Install the rubber washer (1) and metal
washer (2) onto the threaded mount-
ing shank. Thread the nut (3) onto the
mounting shank. Lock the nut (3) into
position by tightening the screws (4). Do
not overtighten.
1
2
2
1
3
6
1
3
4
1
2
3
4
Ceramic cartridge
Manufactured to include no more than 0.25% weighted average lead content
on wetted surfaces
5.
Insert the soap assembly (1) through
the selected hole in the sink. Secure the
soap assembly to the sink with the soap
dispenser mounting nut (2) provided.
From under the sink, screw the soap
bottle (3) onto the soap assembly (1)
shank. Insert the soap pump (4) down
into the soap assembly (1).
6.
Thread the nut (1) on the supply line
onto the outlet of the water supply
valve (2) and tighten with a wrench. Do
not overtighten.
NOTE: The hot side inlet tube is
indicated by a label. Avoid twisting
wires together or placing the wires
close to each other and damaging.
IMPORTANT: After installation is
7.
completed, turn on the hot and cold
water supply. Check for leaks. Pull the
hose assembly out of the spout and
3
remove the spray head by unscrewing
2
it from the hose in a counterclockwise
direction. Be sure to hold the end of
4
the hose down into the sink and turn
the faucet on to the warm position
where it mixes hot and cold water.
5
Flush the water lines for one minute.
This flushes away any debris that could
cause damage to internal parts. Check
for leaks. Re-tighten any connections if
necessary, but do not overtighten.
Reinstall the spray head by hand
tightening it back onto the spray hose.
2
SPECIFICATIONS
5
6
1
2
7
www.homewerksww.com
4
1
2
3

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Tosca h91k-51d-ss

Tabla de contenido