Accessories - Amana ART104TFDW Instrucciones Para El Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

If you experience
Possible Causes and/or Recommended Solutions
The door will not
The door is blocked open - Move food packages away from door. Push bin or shelf back into the correct
close completely
position. Make sure the crisper cover is fully pushed in, so that the back rests on the supports.
The door is
Gaskets are dirty or sticky - Clean gaskets and contact surfaces with mild soap and warm water. Rinse
difficult to open
and dry with soft cloth.
Temperature is
New Installation - Allow 24 hours following installation for the refrigerator to cool completely.
too warm
Door(s) opened often or not closed completely - Allows warm air to enter refrigerator. Minimize door
openings and keep doors fully closed.
A large amount of warm food has been recently added - Allow several hours for refrigerator to return to
normal temperature.
Check that the Temperature Control(s) are set correctly for the surrounding conditions - Adjust the
controls to one setting colder. Check temperature in 24 hours. See "Using the Control(s)."
There is interior
Humid room - Contributes to moisture buildup in the refrigerator.
moisture buildup
Door(s) opened often or not closed completely - Allows humid air to enter the refrigerator. Minimize door
NOTE: Some
openings and keep door fully closed.
moisture buildup is
normal.
The ice maker is
The ice maker is not connected to a water supply - Connect refrigerator to water supply and turn water
not producing ice
shutoff valve fully open.
or not enough ice
A kink in the line can reduce water flow - Straighten the water source line.
(on some models)
Ice maker is not turned on - Make sure the ice maker wire shutoff arm or switch (depending on model) is in
the ON position.
New installation - Wait 24 hours after ice maker installation for ice production to begin. Wait 3 days for full
ice production.
Large amount of ice recently removed - Allow sufficient time for ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm - Remove ice from the ejector arm with a plastic utensil.
A reverse osmosis water filtration system connected to your cold water supply can decrease water
pressure - See "Water Supply Requirements."
The ice cubes are
The water valve is not completely open - Turn the water shutoff valve fully open.
hollow or small
A kink in the line can reduce water flow - Straighten the water source line.
(on some models)
A reverse osmosis water filtration system connected to your cold water supply can decrease water
NOTE: This is an
pressure - See "Water Supply Requirements."
indication of low
water pressure.
If questions regarding water pressure remain, call a licensed, qualified plumber.
Off-taste, odor or
New plumbing connections can cause discolored or off-flavored ice - Discard the ice and wash the ice
gray color in the
storage bin. Allow 24 hours for the ice maker to make new ice, and discard the first 3 batches of ice
ice (on some
produced.
models)
Ice stored too long can develop an off-taste - Discard ice. Wash ice bin. Allow 24 hours for ice maker to
make new ice.
Food odor transferring to ice - Use airtight, moisture proof packaging to store food.
There are minerals (such as sulfur) in the water - A water filter may need to be installed to remove the
minerals.
The following accessories are available for your refrigerator. To
order, contact us and ask for the Part Number.
In the U.S.A., visit our web page www.amana.com or call
1-800-442-9991.
In Canada, visit our web page www.amanacanada.ca
or call 1-800-807-6777.
All manuals and user guides at all-guides.com

ACCESSORIES

affresh
In U.S.A., order Part #W10355016
In Canada, order Part #W10355016B
affresh
In U.S.A., order Part #W10355049
In Canada, order Part #W10355049B
affresh
In U.S.A., order Part #W10355010
In Canada, order Part #W10355010B
®
Stainless Steel Cleaner:
®
Stainless Steel Wipes:
®
Kitchen & Appliance Cleaner:
15

Publicidad

Tabla de contenido
loading

Tabla de contenido