Know Your Product; Operation; Prior To Initial Operation - Redstone RS 722 B Instrucciones De Uso Originales

▪ Before using the tool on an actual work piece,
switch on and let it run for a while. Operate
the tool at least 200 mm away from your face
and body.
▪ Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
▪ Hold the power tool firmly.
▪ Keep your hands away from rotating parts. Do
not touch the bit or the work piece immedi-
ately after operation - they may be extremely
hot and you may get serious burns.
▪ The tool must be used only for its prescribed
purpose. Any use other than those mentioned
in this Manual will be considered a case of
misuse. The user and not the manufacturer
shall be liable for any damage or injury result-
ing from such cases of misuse.
▪ To use this tool properly, you must observe
the safety regulations, the assembly instruc-
tions and the operating instructions found in
this Manual. All persons who use and serv-
ice the machine have to be acquainted with
this Manual and must be informed about its
potential hazards. Children and frail people
must not use this tool. Children should be su-
pervised at all times if they are in the area in
which the tool is being used. It is also impera-
tive that you observe the accident prevention
regulations in force in your area. The same
applies for general rules of occupational
health and safety.
▪ The manufacturer shall not be liable for any
changes made to the tool nor for any damage
resulting from such changes.
Even when the tool is used as prescribed it is
not possible to eliminate all residual risk factors.
The following hazards may arise in connection
with the tool's construction and design:
▪ Damage to hearing if effective hearing protec-
tion is not worn.
▪ Always unplug the machine prior to any ad-
justment, servicing or maintenance including
replacing the accessories.
▪ The power tools must not be used outdoors in
rainy weather, or in moist environment (after
rain) or in close vicinity with easily flammable
liquids and gases. The working place should
be well lit.

Know your product

Before using the power tool, familiarize your-
self with all the operating features and safety
requirements.
16
EN
Use the tool and accessories only for the ap-
plications intended. All other applications are
expressly ruled out.
1. Spindle
2. Wheel guard
3. Support flange
4. Diamond cup wheel
5. Fixing flange
6. Auxiliary handle
7. ON/OFF switch
8. ON/OFF switch locking button
9. Spindle lock button
10. Rubber seal
11. Fastening bracket
12. Flat face support washer
13. Screw

Operation

This power tool is supplied from single-phase
alternating current mains only. It is double insu-
lated according to EN 60745-1, IEC 60745 and
can be connected to grounded or not grounded
sockets. This power tool is radio suppressed in
compliance with EMC Directive 2004/108/EC.
This power tool is designed for rough and fine
grinding concrete and rock material with the pur-
pose of refurbishing before laying plaster and
protective coating. The machine is designed for
dry grinding only.

PRIOR TO INITIAL OPERATION

▪ The machine may be delivered with the wheel
guard mounted at the factory. Ensure that the
wheel guard is mounted properly and fixed
reliably prior to the initial and any following
operation.
▪ The machine may be delivered with the wheel
mounted at the factory. Ensure that the wheel
is mounted properly and fixed reliably prior to
the initial and any following operation.
▪ Make sure the power supply voltage corre-
sponds to the value indicated on the name
plate with technical data of the tool.
▪ Always check the position of ON/OFF switch.
The power tool must be connected to the
power supply socket only when this switch is
in OFF position.
▪ Make sure that the cord and the plug are in
order. If the replacement of the supply cord is
necessary, this has to be done by the manu-
facturer or his agent in order to avoid a safety
hazard.
RS 722 B