Sirius SLT955 Instrucciones Para La Instalación, Uso Y Mantenimiento página 15

INSTALLATION
To install the product is necessary to make
a countertop minimum depth of at least 220
mm up to a maximum of 400 mm. For greater
depths it is necessary to ask the special KIT
with mounting brackets for ceiling depth
from 400mm to 580mm.
For proper operation, we recommend to in-
stall the appliance at a maximum distance of
2000 - 2100 mm from the floor.
Attention: If a remote motor is installed
in the same compartment as products
SLT955/SLT956, check the overall dimen-
sions of the remote motor.
You can choose the side of the hood from
which to run off the sucked air; there are air
outlets of rectangular shape on three sides
of the hood.
After choosing the best location, set up the
channel, the supply provided includes an air
outlet flange of rectangular shape 230x80mm
to be installed on the chosen outlet. Leave
closed the air exhaust holes are not used.
There is also a fitting included, that allows
the use of tubes with a diameter equal to 150
mm (see fig. 1), if you plan to create a circular
air outlet duct.
Identify a reference point compared to the
exact centre for hood installation in the solid
ceiling. Then mark out the area for the holes
to be drilled, at the points shown in figure
2 for the item SLT955 or fig. 3 for the item
SLT956.
Make the holes in the solid ceiling, using a
suitable 8 mm helical drill bit and insert the
plugs provided. It is sufficient to drill the outer
holes shown in figure 2 or figure 3; the inner
holes can be drilled after installing the hood.
Adjust the excursion of the fixing brackets
according to the depth of the niche; min.
220mm, max. 400mm as, shown in Fig. 4.
Tighten strongly the fastening screws of the
brackets immediately after you placed them into
position.
Place the cooker hood in an established area and
fix it with the screws supplied (see fig. 5).
Perform the holes into the ceiling in correspon-
dence of the central holes of the brackets and
fix definitively the product by applying the re-
maining screws.
Make the electrical connection (see fig. 6) and
connect the air discharge pipe following the in-
structions given in the related section DUCTING
SYSTEMS.
If installing an SLT 955 MODUL LIGHT or SLT
956 MODUL LIGHT, connect the electrical wire
of the MODUL LIGHT hood to the connectors
shown in figure 6 on SLT955 or SLT956.
Connect the external motor's cable to the
terminal board found in side the plastic box
of the wiring . Make sure to respect the colors
of cables when perfor ming the electrical con-
nection (fig.6).
Refit the grease filter and close the glass pa-
nels.
Install the plasterboard sheet making sure that
it fits perfectly to the metal edge of the hood
(Fig 12).
The dimensions of the hole to make in the pla-
sterboard are:
- SLT955: 502 mm X 502 mm with two cur-
ved sides R551,
- SLT956: 982 mm X 222 mm, use the drilling
template provided.
Use the 3.5 x 22 screws supplied to fix the pla-
sterboard to the cooker hood and insert them
using the appropriate hole template.
We recommend at least 12 screws to obtain a
good fixation.
In case the hood is provided with an internal pa-
nel be covered in plasterboard, wood or other
material, make a sheet of the following dimen-
sions:
- SLT955: 448 mm X 448 mm with R524 on
the corners,
- SLT956: 928 mm X 168 mm, use the drilling
template supplied.
Install the sheet to the panel (fig. 7), using the
screws provided in the case of plasterboard or
using the appropriate adhesive for the type of
material to be secured.
Caution: Do not use screws longer than the
panel thickness, maximum 3.5 x 22.
12