Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
H-2452, H-2453
π
H-2454, H-2455
WIRE CORNER SHELVING
Post x 5
Figure 1
Figure 2
Figure 3
PAGE 1 OF 6
1-800-295-5510
uline.com
PARTS
Shelf x 4
ASSEMBLY
POST ASSEMBLY
1. Connect post tops to post bottoms with a post
connector. (See Figure 1)
TO INSTALL SELF-LEVELERS
1.
Make sure post is positioned as shown. (See Figure 2)
2. Insert self-levelers into open end of post. Use a rubber
mallet/hammer or tap on ground to slide self-leveler
into post.
3. Repeat step 2 for all other posts.
TO INSTALL OPTIONAL CASTERS
1.
Make sure post is positioned as shown. (See Figure 3)
2. Engage the wheel brakes to keep casters from rolling
during assembly. Use a rubber mallet to tap caster
stem into posts. (See Figure 3)
Pour le français, consulter les pages 5-6.
Shelf Support x 20 Sets
NOTE: Post tops have a black plastic cap in the
top of the post.
NOTE: If installing casters, do not install self-
levelers.
Para Español, vea páginas 3-4.
Self- Leveler x 5
0221 IH-2452
Publicidad
Manuales relacionados para Uline H-2452
Resumen de contenidos para Uline H-2452
- Página 1 Para Español, vea páginas 3-4. Pour le français, consulter les pages 5-6. H-2452, H-2453 π 1-800-295-5510 H-2454, H-2455 uline.com WIRE CORNER SHELVING PARTS Post x 5 Shelf x 4 Shelf Support x 20 Sets Self- Leveler x 5 ASSEMBLY POST ASSEMBLY Figure 1 1.
-
Página 2: Unit Assembly
(See Figure 6) 4. Determine the height of the next shelf, snap on Figure 7 supports then add and secure shelf. Repeat Step 4 to add the remaining shelves. (See Figure 7) 1-800-295-5510 uline.com PAGE 2 OF 6 0221 IH-2452... -
Página 3: Ensamble
H-2452, H-2453 π 800-295-5510 H-2454, H-2455 uline.mx ESTANTERÍA DE ALAMBRE PARA ESQUINAS PARTES Poste x 5 Repisa x 4 Soporte de Repisa x Set de 20 Autonivelador x 5 ENSAMBLE ENSAMBLE DE LOS POSTES Diagrama 1 Una las partes superiores de los postes a las partes inferiores de los postes usando conectores para postes. -
Página 4: Continuación De Ensamble
4. Determine la altura de la siguiente repisa, inserte a presión los soportes y después agregue y asegure la repisa. Repita el Paso 4 para agregar las repisas restantes. (Vea Diagrama 7) Diagrama 6 Diagrama 7 800-295-5510 uline.mx PAGE 4 OF 6 0221 IH-2452... -
Página 5: Rayonnage Angulaire En Fil De Métal
H-2452, H-2453 π 1-800-295-5510 H-2454, H-2455 uline.ca RAYONNAGE ANGULAIRE EN FIL DE MÉTAL PIÈCES Montant x 5 Tablette x 4 Ensemble de support de Dispositif tablette x 20 d'autonivellement x 5 ASSEMBLAGE ASSEMBLAGE DES MONTANTS Figure 1 Raccordez les montants supérieurs aux montants inférieurs au moyen d'un raccord à... - Página 6 (Voir Figure 6) 4. Déterminez la hauteur de la tablette suivante, Figure 7 encliquetez les supports, puis ajoutez et fixez la tablette. Répétez l'étape 4 pour ajouter les tablettes restantes. (Voir Figure 7) 1-800-295-5510 uline.ca PAGE 6 OF 6 0221 IH-2452...